Omnitron Systems Technology RS-232 user manual Operation, Operating Procedure

Page 50

Section 5

OPERATION

Operating Procedure

The Omni reader is easy to operate. Just follow these simple steps:

1.Make sure the reader is properly connected (see sections 2 and 6) and is re- ceiving sufficient power. (See Section 6, Troubleshooting, if there is a cabling or power problem.)

2.To read a card, slide the card, in either direction, through the reader slot, with the bar code facing the optical head (LED side) or the magnetic stripe facing the magnetic head (opposite side).

3.Once the entire bar code or magnetic stripe has been read, the LED indicator will light up as green to signal a “good read.” If a good read is not obtained, the LED indicator will light up as red.

4.A beep will also sound to indicate a good read on the bar code or each magnetic track, as appropriate. If all three tracks have been read successfully, the reader will beep three times.

5.The decoded data will be transmitted to the host application.

Note: Output data can be verified in Hyper Terminal (or another serial communication program).

44

Image 50
Contents Omnitm Page Limited Warranty Agency ApprovedPage Table of Contents Page Description SectionIntroduction Installation Host ConnectionsBar Code Input ConfigurationConfiguration Setup Procedure Magnetic Stripe InputExample Default Settings Serial Interface Parameters Group EBaud Rate ParityGeneral Selections Group B Stop BitScan Verification Beep VolumeCode/Track ID Code ID Definition Group Enter one character for the new IDBar Code Message Formatting Selections Group C Bar Code Terminator CharacterBar Code Preamble Bar Code PostambleMagnetic Stripe Formatting Selections Group D Magnetic Stripe Terminator CharacterMagnetic Stripe Preamble Magnetic Stripe PostambleMinimum and Maximum Length Options Bar Code SelectionsIndustrial Bar Codes Group F Full Ascii Code 39 SettingsEnable/Disable Code Check Digit Interleaved 2 of 5 SettingsEnable/Disable Interleaved 2 Send Start/Stop CharactersFebraban Conversion Fixed LengthIndustrial 2 of 5 Settings Enable/Disable Industrial 2Code 128 Setting Codabar Settings Enable/Disable CodabarEnable/Disable MSI/Plessey MSI/Plessey SettingsTelepen Setting Enable/Disable TelepenRetail Bar Codes Group G UPC SettingsEnable/Disable UPC-A Send Check Digit Enable/Disable UPC-ESend Number System Digit UPC-E ExpansionAddendum Required Read Two-Digit AddendumRead Five-Digit Addendum Add Separator SpaceEnable/Disable EAN-8 EAN SettingsEnable/Disable EAN-13 Send Induced Country Code CharacterRead Five-Digit Addendum Do Not Read Five-Digit Addendum Send Start/Stop Sentinel Magnetic Stripe Selections Group HTrack Selection Track Separator Reviewing Configuration SettingsTrack Two Send Accout Number Only H4ENTERSELECTED CharacterenterMSI Data Editing Data Fields Data Editing Formulas Formula Sequence Code IdlengthmatchdivideaddsendUsing the Data Editing Functions Track 1 %CABREADOE$JANE$R$310 S Jefferson ST?Unmatched Input Send/Do Not Send Data Editing CommandsData Editing On/Off JDENTER0ENTER6ENTER1ENTER2ENTER Select Code IDsSet Length JEENTER0ENTER8ENTERAENTERBENTER Centerdentereenter Match StringCreate a Data Field JFENTER0ENTER7ENTERJgenteraenterbentercenter Dentereenter Search for a Data StringAdd a Data Field Delete One Formula Time DelaySet the Sequence in which Data Fields are Sent JkenteraentercenterbenterExit Data Editing Mode Reset Data Editing GroupReview Configurations Omni Data FlowSymbology Code ExamplesEnter 7ENTER Send BD DLY 09 AD DLYJDENTER0ENTER7ENTER0 JEENTER0ENTER7ENTERMSR Track 1 data Operating Procedure OperationTroubleshooting General ProceduresSerial Interface Problems Scanning Configurations Crlf Default SettingsAppendix a Industrial Bar Codes UPC-A UPC-E EAN-8 Retail BarcodesUPC-A, -E Appendix B Magnetic Stripe FormatAppendix C Magnetic Stripe Standard Data FormatsCalifornia Driver’s License Format Track LRE ID Aamva Driver’s License Format Track Appendix D Full Ascii TableAscii RS-232 Port, Standard DB-9P Connector PIN-OUTSAppendix E USB/RS-232 Interface Installing the DriversAppendix F Page UE Anyway Troubleshooting Checking the Installation and Modifying the COM Port NumberTelling Whether the Installed Device is Type a or Type B Updating the Driver Date DriverRemoving the Driver Versal Serial BUS ControllersID Tech