Omnitron Systems Technology RS-232 Industrial 2 of 5 Settings, Enable/Disable Industrial 2

Page 24

Industrial 2 of 5 Settings:

Enable/Disable Industrial 2 of 5

If enabled, Industrial 2 of 5 symbology will be read, subject to the reading restrictions speciﬁed by this set of options. If disabled, the data from the sym- bology will be disregarded.

SELECTION CODE: F3
Industrial 2 of 5 Enable	A
Industrial 2 of 5 Disable	B

Fixed Length

Industrial 2 of 5 symbols are commonly printed in a ﬁxed format contain- ing a ﬁxed number of characters. If this option is ON, the ﬁrst Interleaved 2 of 5 symbol scanned after power up will set the length of any other symbols scanned afterwards. If the succeeding scans do not match the length of the ﬁrst scan, the scan is rejected by the reader. Power must be reset before an Interleaved 2 of 5 symbol of a different length will be accepted.

SELECTION CODE: F3
Turn On Fixed Length	C
Turn Off Fixed Length	D

18

Image 24

Contents Omnitm Page Limited Warranty Agency ApprovedPage Table of Contents Page Section IntroductionDescription Installation Host ConnectionsConfiguration Configuration Setup ProcedureBar Code Input Magnetic Stripe InputExample Default Settings Serial Interface Parameters Group EBaud Rate ParityGeneral Selections Group B Stop BitBeep Volume Code/Track IDScan Verification Code ID Definition Group Enter one character for the new IDBar Code Message Formatting Selections Group C Bar Code Terminator CharacterBar Code Preamble Bar Code PostambleMagnetic Stripe Formatting Selections Group D Magnetic Stripe Terminator CharacterMagnetic Stripe Preamble Magnetic Stripe PostambleBar Code Selections Industrial Bar Codes Group FMinimum and Maximum Length Options Code 39 Settings Enable/Disable CodeFull Ascii Interleaved 2 of 5 Settings Enable/Disable Interleaved 2Check Digit Send Start/Stop CharactersFebraban Conversion Fixed LengthIndustrial 2 of 5 Settings Enable/Disable Industrial 2Code 128 Setting Codabar Settings Enable/Disable CodabarMSI/Plessey Settings Telepen SettingEnable/Disable MSI/Plessey Enable/Disable TelepenUPC Settings Enable/Disable UPC-ARetail Bar Codes Group G Enable/Disable UPC-E Send Number System DigitSend Check Digit UPC-E ExpansionRead Two-Digit Addendum Read Five-Digit AddendumAddendum Required Add Separator SpaceEAN Settings Enable/Disable EAN-13Enable/Disable EAN-8 Send Induced Country Code CharacterRead Five-Digit Addendum Do Not Read Five-Digit Addendum Magnetic Stripe Selections Group H Track SelectionSend Start/Stop Sentinel Reviewing Configuration Settings Track Two Send Accout Number OnlyTrack Separator H4ENTERSELECTED CharacterenterMSI Data Editing Data Fields Data Editing Formulas Formula Sequence Code IdlengthmatchdivideaddsendUsing the Data Editing Functions Track 1 %CABREADOE$JANE$R$310 S Jefferson ST?Data Editing Commands Data Editing On/OffUnmatched Input Send/Do Not Send Select Code IDs Set LengthJDENTER0ENTER6ENTER1ENTER2ENTER Match String Create a Data FieldJEENTER0ENTER8ENTERAENTERBENTER Centerdentereenter JFENTER0ENTER7ENTERSearch for a Data String Add a Data FieldJgenteraenterbentercenter Dentereenter Time Delay Set the Sequence in which Data Fields are SentDelete One Formula JkenteraentercenterbenterReset Data Editing Group Review ConfigurationsExit Data Editing Mode Omni Data FlowSymbology Code ExamplesSend BD DLY 09 AD DLY JDENTER0ENTER7ENTER0Enter 7ENTER JEENTER0ENTER7ENTERMSR Track 1 data Operating Procedure OperationTroubleshooting General ProceduresSerial Interface Problems Scanning Configurations Default Settings Appendix aCrlf Industrial Bar Codes Retail Barcodes UPC-A, -EUPC-A UPC-E EAN-8 Appendix B Magnetic Stripe FormatAppendix C Magnetic Stripe Standard Data FormatsCalifornia Driver’s License Format Track LRE ID Aamva Driver’s License Format Track Appendix D Full Ascii TableAscii Connector PIN-OUTS Appendix ERS-232 Port, Standard DB-9P Installing the Drivers Appendix FUSB/RS-232 Interface Page UE Anyway Checking the Installation and Modifying the COM Port Number Telling Whether the Installed Device is Type a or Type BTroubleshooting Updating the Driver Date DriverRemoving the Driver Versal Serial BUS ControllersID Tech