Omnitron Systems Technology RS-232 user manual Bar Code Selections, Industrial Bar Codes Group F

Page 20

Bar Code Selections

Bar code selections for the Omni are separated into two groups: Industrial and Retail. Industrial bar codes may contain a variable number of characters. Retail bar codes always contain a specific number of characters.

Industrial Bar Codes (Group F)

1.Enter INDUSTRIAL BAR CODE SETUP MODE by typing /E/D/FF.

2.Press <ENTER>. The reader should beep twice.

3.Type the two-character selection code for the bar code symbology you wish to change.

4.Press <ENTER>. The reader should beep twice.

5.Type the one-character code for the change you wish to make.

6.Press <ENTER>. The reader should beep twice.

7.Save the change and exit the Industrial Bar Code Setup Mode by typing FZ.

8.Press <ENTER>. The reader should beep four times.

Note: To review the group’s current setting(s), type FY<ENTER> while in the Indus- trial Bar Code Setup Mode. To reset the current setting(s) to its group default, type FX<ENTER> while in Industrial Bar Code Setup Mode.

Minimum and Maximum Length Options

You can set minimum and maximum length standards for a particular indus- trial bar code symbology. (You cannot set a minimum or maximum length for a retail bar code.)

Minimum length sets the minimum number of data characters that will be accepted for this symbology. If the minimum length is set higher than the maximum length, all readings will be rejected.

Maximum length sets the maximum number of data characters that will be accepted for this symbology. If the maximum length is set lower than the minimum length, all readings will be rejected.

To set the minimum and maximum length for a particular symbology:

1.Enter Setup Mode by typing /E/D/FF.

2.Press <ENTER>. The reader should beep twice.

3.Enter the selection code for the particular symbology selected (such as F4<ENTER> for Code 128). The reader should beep twice.

4.Enter FU<ENTER> for minimum or FV<ENTER> for maximum. The reader should beep twice.

14

Image 20
Contents Omnitm Page Limited Warranty Agency ApprovedPage Table of Contents Page Description SectionIntroduction Installation Host ConnectionsConfiguration Configuration Setup ProcedureBar Code Input Magnetic Stripe InputExample Default Settings Serial Interface Parameters Group EBaud Rate ParityGeneral Selections Group B Stop BitScan Verification Beep VolumeCode/Track ID Code ID Definition Group Enter one character for the new IDBar Code Message Formatting Selections Group C Bar Code Terminator CharacterBar Code Preamble Bar Code PostambleMagnetic Stripe Formatting Selections Group D Magnetic Stripe Terminator CharacterMagnetic Stripe Preamble Magnetic Stripe PostambleMinimum and Maximum Length Options Bar Code SelectionsIndustrial Bar Codes Group F Full Ascii Code 39 SettingsEnable/Disable Code Interleaved 2 of 5 Settings Enable/Disable Interleaved 2Check Digit Send Start/Stop CharactersFebraban Conversion Fixed LengthIndustrial 2 of 5 Settings Enable/Disable Industrial 2Code 128 Setting Codabar Settings Enable/Disable CodabarMSI/Plessey Settings Telepen SettingEnable/Disable MSI/Plessey Enable/Disable TelepenRetail Bar Codes Group G UPC SettingsEnable/Disable UPC-A Enable/Disable UPC-E Send Number System DigitSend Check Digit UPC-E ExpansionRead Two-Digit Addendum Read Five-Digit AddendumAddendum Required Add Separator SpaceEAN Settings Enable/Disable EAN-13Enable/Disable EAN-8 Send Induced Country Code CharacterRead Five-Digit Addendum Do Not Read Five-Digit Addendum Send Start/Stop Sentinel Magnetic Stripe Selections Group HTrack Selection Reviewing Configuration Settings Track Two Send Accout Number OnlyTrack Separator H4ENTERSELECTED CharacterenterMSI Data Editing Data Fields Data Editing Formulas Formula Sequence Code IdlengthmatchdivideaddsendUsing the Data Editing Functions Track 1 %CABREADOE$JANE$R$310 S Jefferson ST?Unmatched Input Send/Do Not Send Data Editing CommandsData Editing On/Off JDENTER0ENTER6ENTER1ENTER2ENTER Select Code IDsSet Length Match String Create a Data FieldJEENTER0ENTER8ENTERAENTERBENTER Centerdentereenter JFENTER0ENTER7ENTERJgenteraenterbentercenter Dentereenter Search for a Data StringAdd a Data Field Time Delay Set the Sequence in which Data Fields are SentDelete One Formula JkenteraentercenterbenterReset Data Editing Group Review ConfigurationsExit Data Editing Mode Omni Data FlowSymbology Code ExamplesSend BD DLY 09 AD DLY JDENTER0ENTER7ENTER0Enter 7ENTER JEENTER0ENTER7ENTERMSR Track 1 data Operating Procedure OperationTroubleshooting General ProceduresSerial Interface Problems Scanning Configurations Crlf Default SettingsAppendix a Industrial Bar Codes UPC-A UPC-E EAN-8 Retail BarcodesUPC-A, -E Appendix B Magnetic Stripe FormatAppendix C Magnetic Stripe Standard Data FormatsCalifornia Driver’s License Format Track LRE ID Aamva Driver’s License Format Track Appendix D Full Ascii TableAscii RS-232 Port, Standard DB-9P Connector PIN-OUTSAppendix E USB/RS-232 Interface Installing the DriversAppendix F Page UE Anyway Troubleshooting Checking the Installation and Modifying the COM Port NumberTelling Whether the Installed Device is Type a or Type B Updating the Driver Date DriverRemoving the Driver Versal Serial BUS ControllersID Tech