Omnitron Systems Technology RS-232 user manual

Page 66

3. Go to START/CONTROL PANEL/ADD OR REMOVE PROGRAMS.

If you find “ID TECH USB Serial Driver V3.0,” leave it. The correct drivers are already installed. Proceed to the next step.

If you find either “ID TECH USB Serial Converter Drivers” or “FTDI USB Serial Drivers,” remove them. Then proceed to the next step.

If you find nothing, proceed to the next step.

4.Plug an ID TECH USB/RS-232 device into one of the USB ports. A “Found new hardware wizard” window should appear on the screen. (If it does not appear, please go to “Checking the Installation and Modifying the COM Port Number.”)

5.Select “Install from a list or specific location” and click NEXT. The host should display another window: “Please choose your search and installation options”

6.Select “Don’t search, I will choose the driver to install” and click NEXT. You will be asked to select the hardware type. Select “Show all devices” and click NEXT.

7.You will be asked to “select the device driver you want to install for this hardware.” Select SHOW ALL DEVICES and HAVE DISK and then click NEXT.

8.The INSTALL FROM DISK window will appear. Click BROWSE.

9.The LOCATE FILE window will appear. Find C:\ID TECH USB Serial Driver V3.0. Select FTDIBUS.INF and click OPEN.

10.Click OK on the next window. The following will appear: “Select the device driver you want to install for this hardware.” You will also notice a warning that the driver is not digitally signed. Click NEXT. A Windows XP warning will appear: “This driver is not digitally signed.” Click CONTINUE ANYWAY.

60

Image 66
Contents Omnitm Page Limited Warranty Agency ApprovedPage Table of Contents Page Section IntroductionDescription Installation Host ConnectionsBar Code Input ConfigurationConfiguration Setup Procedure Magnetic Stripe InputExample Default Settings Serial Interface Parameters Group EBaud Rate ParityGeneral Selections Group B Stop BitBeep Volume Code/Track IDScan Verification Code ID Definition Group Enter one character for the new IDBar Code Message Formatting Selections Group C Bar Code Terminator CharacterBar Code Preamble Bar Code PostambleMagnetic Stripe Formatting Selections Group D Magnetic Stripe Terminator CharacterMagnetic Stripe Preamble Magnetic Stripe PostambleBar Code Selections Industrial Bar Codes Group FMinimum and Maximum Length Options Code 39 Settings Enable/Disable CodeFull Ascii Check Digit Interleaved 2 of 5 SettingsEnable/Disable Interleaved 2 Send Start/Stop CharactersFebraban Conversion Fixed LengthIndustrial 2 of 5 Settings Enable/Disable Industrial 2Code 128 Setting Codabar Settings Enable/Disable CodabarEnable/Disable MSI/Plessey MSI/Plessey SettingsTelepen Setting Enable/Disable TelepenUPC Settings Enable/Disable UPC-ARetail Bar Codes Group G Send Check Digit Enable/Disable UPC-ESend Number System Digit UPC-E ExpansionAddendum Required Read Two-Digit AddendumRead Five-Digit Addendum Add Separator SpaceEnable/Disable EAN-8 EAN SettingsEnable/Disable EAN-13 Send Induced Country Code CharacterRead Five-Digit Addendum Do Not Read Five-Digit Addendum Magnetic Stripe Selections Group H Track SelectionSend Start/Stop Sentinel Track Separator Reviewing Configuration SettingsTrack Two Send Accout Number Only H4ENTERSELECTED CharacterenterMSI Data Editing Data Fields Data Editing Formulas Formula Sequence Code IdlengthmatchdivideaddsendUsing the Data Editing Functions Track 1 %CABREADOE$JANE$R$310 S Jefferson ST?Data Editing Commands Data Editing On/OffUnmatched Input Send/Do Not Send Select Code IDs Set LengthJDENTER0ENTER6ENTER1ENTER2ENTER JEENTER0ENTER8ENTERAENTERBENTER Centerdentereenter Match StringCreate a Data Field JFENTER0ENTER7ENTERSearch for a Data String Add a Data FieldJgenteraenterbentercenter Dentereenter Delete One Formula Time DelaySet the Sequence in which Data Fields are Sent JkenteraentercenterbenterExit Data Editing Mode Reset Data Editing GroupReview Configurations Omni Data FlowSymbology Code ExamplesEnter 7ENTER Send BD DLY 09 AD DLYJDENTER0ENTER7ENTER0 JEENTER0ENTER7ENTERMSR Track 1 data Operating Procedure OperationTroubleshooting General ProceduresSerial Interface Problems Scanning Configurations Default Settings Appendix aCrlf Industrial Bar Codes Retail Barcodes UPC-A, -EUPC-A UPC-E EAN-8 Appendix B Magnetic Stripe FormatAppendix C Magnetic Stripe Standard Data FormatsCalifornia Driver’s License Format Track LRE ID Aamva Driver’s License Format Track Appendix D Full Ascii TableAscii Connector PIN-OUTS Appendix ERS-232 Port, Standard DB-9P Installing the Drivers Appendix FUSB/RS-232 Interface Page UE Anyway Checking the Installation and Modifying the COM Port Number Telling Whether the Installed Device is Type a or Type BTroubleshooting Updating the Driver Date DriverRemoving the Driver Versal Serial BUS ControllersID Tech