Omnitron Systems Technology RS-232 user manual Reviewing Configuration Settings, Track Separator

Page 34

Track Two Send Accout Number Only

Track Two of a magnetically encoded credit card includes the account number information as well as other information. If this option is selected, all other- data contained on the track is suppressed before transmission.

SELECTION CODE: H3

Track 2 Send Account Number Only

A

Track 2 Not Limited to Account Number

B

Track Separator

One character from the Full ASCII Table: This option allows the user to select the character used to separate data decoded from each track when using mul- tiple track magnetic stripe readers.

H4<ENTER><SELECTED CHARACTER><ENTER>

Note: For no track separator, enter N. Default is <ENTER>.

Reviewing Configuration Settings

The reader’s current settings can be reviewed by following these steps:

1.Locate the group that contains the settings you want to review.

2.On an AT-compatible computer, enter any communication program. (Hyper Terminal is recommend in the Windows environment.)

3.Enter the setup mode for that group by typing /E/D/FX <Enter>. (X in this case is the single alpha character identified with the group located in Step 1.)

4.The reader will respond with two beeps after <ENTER> is depressed.

5.Review the settings for the group by typing XY<ENTER>. (X is the same single alpha character as typed in Step 3.)

6.After <ENTER> is depressed, the reader will display the current settings for the group onto the screen for user to review, followed by two beeps from the reader. *

7.Exit the setup mode after reviewing the settings by typing XZ <ENTER>. (X is the same single alpha character as typed in Step 3.)

8.The reader will respond with four beeps.

*Hyper Terminal must be configured correctly: Append Line Feed to Incoming Line End.

28

Image 34
Contents Omnitm Page Limited Warranty Agency ApprovedPage Table of Contents Page Introduction SectionDescription Installation Host ConnectionsBar Code Input ConfigurationConfiguration Setup Procedure Magnetic Stripe InputExample Default Settings Serial Interface Parameters Group EBaud Rate ParityGeneral Selections Group B Stop BitCode/Track ID Beep VolumeScan Verification Code ID Definition Group Enter one character for the new IDBar Code Message Formatting Selections Group C Bar Code Terminator CharacterBar Code Preamble Bar Code PostambleMagnetic Stripe Formatting Selections Group D Magnetic Stripe Terminator CharacterMagnetic Stripe Preamble Magnetic Stripe PostambleIndustrial Bar Codes Group F Bar Code SelectionsMinimum and Maximum Length Options Enable/Disable Code Code 39 SettingsFull Ascii Check Digit Interleaved 2 of 5 SettingsEnable/Disable Interleaved 2 Send Start/Stop CharactersFebraban Conversion Fixed LengthIndustrial 2 of 5 Settings Enable/Disable Industrial 2Code 128 Setting Codabar Settings Enable/Disable CodabarEnable/Disable MSI/Plessey MSI/Plessey SettingsTelepen Setting Enable/Disable TelepenEnable/Disable UPC-A UPC SettingsRetail Bar Codes Group G Send Check Digit Enable/Disable UPC-ESend Number System Digit UPC-E ExpansionAddendum Required Read Two-Digit AddendumRead Five-Digit Addendum Add Separator SpaceEnable/Disable EAN-8 EAN SettingsEnable/Disable EAN-13 Send Induced Country Code CharacterRead Five-Digit Addendum Do Not Read Five-Digit Addendum Track Selection Magnetic Stripe Selections Group HSend Start/Stop Sentinel Track Separator Reviewing Configuration SettingsTrack Two Send Accout Number Only H4ENTERSELECTED CharacterenterMSI Data Editing Data Fields Data Editing Formulas Formula Sequence Code IdlengthmatchdivideaddsendUsing the Data Editing Functions Track 1 %CABREADOE$JANE$R$310 S Jefferson ST?Data Editing On/Off Data Editing CommandsUnmatched Input Send/Do Not Send Set Length Select Code IDsJDENTER0ENTER6ENTER1ENTER2ENTER JEENTER0ENTER8ENTERAENTERBENTER Centerdentereenter Match StringCreate a Data Field JFENTER0ENTER7ENTERAdd a Data Field Search for a Data StringJgenteraenterbentercenter Dentereenter Delete One Formula Time DelaySet the Sequence in which Data Fields are Sent JkenteraentercenterbenterExit Data Editing Mode Reset Data Editing GroupReview Configurations Omni Data FlowSymbology Code ExamplesEnter 7ENTER Send BD DLY 09 AD DLYJDENTER0ENTER7ENTER0 JEENTER0ENTER7ENTERMSR Track 1 data Operating Procedure OperationTroubleshooting General ProceduresSerial Interface Problems Scanning Configurations Appendix a Default SettingsCrlf Industrial Bar Codes UPC-A, -E Retail BarcodesUPC-A UPC-E EAN-8 Appendix B Magnetic Stripe FormatAppendix C Magnetic Stripe Standard Data FormatsCalifornia Driver’s License Format Track LRE ID Aamva Driver’s License Format Track Appendix D Full Ascii TableAscii Appendix E Connector PIN-OUTSRS-232 Port, Standard DB-9P Appendix F Installing the DriversUSB/RS-232 Interface Page UE Anyway Telling Whether the Installed Device is Type a or Type B Checking the Installation and Modifying the COM Port NumberTroubleshooting Updating the Driver Date DriverRemoving the Driver Versal Serial BUS ControllersID Tech