Omnitron Systems Technology RS-232 user manual Codabar Settings, Enable/Disable Codabar

Page 26

Codabar Settings:

Enable/Disable Codabar

If enabled, Codabar symbology will be read, subject to the reading restric- tions specified by this set of options. If disabled, the data from the symbology will be disregarded.

SELECTION CODE: F5

 

Codabar Enable

A

Codabar Disable

B

Send Start/Stop Characters

Codabar uses the A, B, C, and D characters as Start and Stop characters, giv- ing 16 unique Start/Stop character combinations. Some applications require that these characters be transmitted with the data while others specify that they must not be sent.

SELECTION CODE: F5

 

Send Start/Stop

C

Do Not Send Start/Stop

D

Check Digit

When Check Digit is selected, the reader takes the last character in the de- coded data stream as a check digit. It then calculates the correct check digit for the remaining data and compares it to the last data character. If it is the same, the data is accepted. If not, the data is rejected. With the Calculate and Send Check Digit option, the reader will send the check digit as part of the data stream. If the Calculate but Do Not Send Check Digit option is selected, the reader will strip it from the data stream before transmission. If the Check Digit is not calculated, the reader will assume the last data character read from the symbol is part of the data stream and will not make a comparison test.

SELECTION CODE: F5

 

Do Not Calculate Check Digit but Send Whole Data Stream

E

Calculate and Send Check Digit

F

Calculate but Do Not Send Check Digit

G

20

Image 26
Contents Omnitm Page Limited Warranty Agency ApprovedPage Table of Contents Page Description SectionIntroduction Installation Host ConnectionsBar Code Input ConfigurationConfiguration Setup Procedure Magnetic Stripe InputExample Default Settings Serial Interface Parameters Group EBaud Rate ParityGeneral Selections Group B Stop BitScan Verification Beep VolumeCode/Track ID Code ID Definition Group Enter one character for the new IDBar Code Message Formatting Selections Group C Bar Code Terminator CharacterBar Code Preamble Bar Code PostambleMagnetic Stripe Formatting Selections Group D Magnetic Stripe Terminator CharacterMagnetic Stripe Preamble Magnetic Stripe PostambleMinimum and Maximum Length Options Bar Code SelectionsIndustrial Bar Codes Group F Full Ascii Code 39 SettingsEnable/Disable Code Check Digit Interleaved 2 of 5 SettingsEnable/Disable Interleaved 2 Send Start/Stop CharactersFebraban Conversion Fixed LengthIndustrial 2 of 5 Settings Enable/Disable Industrial 2Code 128 Setting Codabar Settings Enable/Disable CodabarEnable/Disable MSI/Plessey MSI/Plessey SettingsTelepen Setting Enable/Disable TelepenRetail Bar Codes Group G UPC SettingsEnable/Disable UPC-A Send Check Digit Enable/Disable UPC-ESend Number System Digit UPC-E ExpansionAddendum Required Read Two-Digit AddendumRead Five-Digit Addendum Add Separator SpaceEnable/Disable EAN-8 EAN SettingsEnable/Disable EAN-13 Send Induced Country Code CharacterRead Five-Digit Addendum Do Not Read Five-Digit Addendum Send Start/Stop Sentinel Magnetic Stripe Selections Group HTrack Selection Track Separator Reviewing Configuration SettingsTrack Two Send Accout Number Only H4ENTERSELECTED CharacterenterMSI Data Editing Data Fields Data Editing Formulas Formula Sequence Code IdlengthmatchdivideaddsendUsing the Data Editing Functions Track 1 %CABREADOE$JANE$R$310 S Jefferson ST?Unmatched Input Send/Do Not Send Data Editing CommandsData Editing On/Off JDENTER0ENTER6ENTER1ENTER2ENTER Select Code IDsSet Length JEENTER0ENTER8ENTERAENTERBENTER Centerdentereenter Match StringCreate a Data Field JFENTER0ENTER7ENTERJgenteraenterbentercenter Dentereenter Search for a Data StringAdd a Data Field Delete One Formula Time DelaySet the Sequence in which Data Fields are Sent JkenteraentercenterbenterExit Data Editing Mode Reset Data Editing GroupReview Configurations Omni Data FlowSymbology Code ExamplesEnter 7ENTER Send BD DLY 09 AD DLYJDENTER0ENTER7ENTER0 JEENTER0ENTER7ENTERMSR Track 1 data Operating Procedure OperationTroubleshooting General ProceduresSerial Interface Problems Scanning Configurations Crlf Default SettingsAppendix a Industrial Bar Codes UPC-A UPC-E EAN-8 Retail BarcodesUPC-A, -E Appendix B Magnetic Stripe FormatAppendix C Magnetic Stripe Standard Data FormatsCalifornia Driver’s License Format Track LRE ID Aamva Driver’s License Format Track Appendix D Full Ascii TableAscii RS-232 Port, Standard DB-9P Connector PIN-OUTSAppendix E USB/RS-232 Interface Installing the DriversAppendix F Page UE Anyway Troubleshooting Checking the Installation and Modifying the COM Port NumberTelling Whether the Installed Device is Type a or Type B Updating the Driver Date DriverRemoving the Driver Versal Serial BUS ControllersID Tech