Omnitron Systems Technology RS-232 user manual ID Tech

Page 71

ID TECH

10721 Walker Street

Cypress, California 90630

(714)761-6368 www.id-tech.net

80028503-004

Rev. A R01/05

#428

Image 71

Contents Omnitm Page Agency Approved Limited WarrantyPage Table of Contents Page Description SectionIntroduction Host Connections InstallationMagnetic Stripe Input ConfigurationConfiguration Setup Procedure Bar Code InputExample Serial Interface Parameters Group E Default SettingsParity Baud RateStop Bit General Selections Group BScan Verification Beep VolumeCode/Track ID Enter one character for the new ID Code ID Definition GroupBar Code Terminator Character Bar Code Message Formatting Selections Group CBar Code Postamble Bar Code PreambleMagnetic Stripe Terminator Character Magnetic Stripe Formatting Selections Group DMagnetic Stripe Postamble Magnetic Stripe PreambleMinimum and Maximum Length Options Bar Code SelectionsIndustrial Bar Codes Group F Full Ascii Code 39 SettingsEnable/Disable Code Send Start/Stop Characters Interleaved 2 of 5 SettingsEnable/Disable Interleaved 2 Check DigitFixed Length Febraban ConversionEnable/Disable Industrial 2 Industrial 2 of 5 SettingsCode 128 Setting Enable/Disable Codabar Codabar SettingsEnable/Disable Telepen MSI/Plessey SettingsTelepen Setting Enable/Disable MSI/PlesseyRetail Bar Codes Group G UPC SettingsEnable/Disable UPC-A UPC-E Expansion Enable/Disable UPC-ESend Number System Digit Send Check DigitAdd Separator Space Read Two-Digit AddendumRead Five-Digit Addendum Addendum RequiredSend Induced Country Code Character EAN SettingsEnable/Disable EAN-13 Enable/Disable EAN-8Read Five-Digit Addendum Do Not Read Five-Digit Addendum Send Start/Stop Sentinel Magnetic Stripe Selections Group HTrack Selection H4ENTERSELECTED Characterenter Reviewing Configuration SettingsTrack Two Send Accout Number Only Track SeparatorMSI Data Editing Data Fields Data Editing Formulas Code Idlengthmatchdivideaddsend Formula SequenceTrack 1 %CABREADOE$JANE$R$310 S Jefferson ST? Using the Data Editing FunctionsUnmatched Input Send/Do Not Send Data Editing CommandsData Editing On/Off JDENTER0ENTER6ENTER1ENTER2ENTER Select Code IDsSet Length JFENTER0ENTER7ENTER Match StringCreate a Data Field JEENTER0ENTER8ENTERAENTERBENTER CenterdentereenterJgenteraenterbentercenter Dentereenter Search for a Data StringAdd a Data Field Jkenteraentercenterbenter Time DelaySet the Sequence in which Data Fields are Sent Delete One FormulaOmni Data Flow Reset Data Editing GroupReview Configurations Exit Data Editing ModeExamples Symbology CodeJEENTER0ENTER7ENTER Send BD DLY 09 AD DLYJDENTER0ENTER7ENTER0 Enter 7ENTERMSR Track 1 data Operation Operating ProcedureGeneral Procedures TroubleshootingSerial Interface Problems Scanning Configurations Crlf Default SettingsAppendix a Industrial Bar Codes UPC-A UPC-E EAN-8 Retail BarcodesUPC-A, -E Magnetic Stripe Format Appendix BMagnetic Stripe Standard Data Formats Appendix CCalifornia Driver’s License Format Track LRE ID Aamva Driver’s License Format Track Full Ascii Table Appendix DAscii RS-232 Port, Standard DB-9P Connector PIN-OUTSAppendix E USB/RS-232 Interface Installing the DriversAppendix F Page UE Anyway Troubleshooting Checking the Installation and Modifying the COM Port NumberTelling Whether the Installed Device is Type a or Type B Date Driver Updating the DriverVersal Serial BUS Controllers Removing the DriverID Tech