Omnitron Systems Technology RS-232 MSI/Plessey Settings, Telepen Setting, Enable/Disable Telepen

Page 27

MSI/Plessey Settings:

Enable/Disable MSI/Plessey

If enabled, MSI/Plessey symbology will be read, subject to the reading restrictions speciﬁed by this set of options. If disabled, the data from the sym- bology will be disregarded.

SELECTION CODE: F7
MSI/Plessey Enable	A
MSI/Plessey Disable	B

Check Digit

The MSI/Plessey symbology requires a check digit, and can optionally have two check digits. The reader can either send the check digit(s) as part of the data, or strip it before transmission to the host.

SELECTION CODE: F7

Send Check Digit	C
Do Not Send Check Digit	D

Select only one of the following check digit schemes:

SELECTION CODE: F7

One Mod 10 Check Digit	E
Two Mod 10 Check Digits	F
Mod 10/Mod 11 Check Digits	G

Telepen Setting:

Enable/Disable Telepen

If enabled, Telepen symbology will be read, subject to the reading restrictions speciﬁed by this set of options. If disabled, the data from the symbology will be disregarded.

SELECTION CODE: F8
Telepen Enable	A
Telepen Disable	B

Numeric / ASCII Mode

If set to Numeric Mode, each original Telepen code will be translated into 2-digit numeric pair. Otherwise, ASCII or Numeric data will be sent out accor-ding to the AIM speciﬁcation.

SELECTION CODE: F8
Numeric Mode	C
ASCII Mode	D

21

Image 27

Contents Omnitm Page Agency Approved Limited WarrantyPage Table of Contents Page Section IntroductionDescription Host Connections InstallationMagnetic Stripe Input ConfigurationConfiguration Setup Procedure Bar Code InputExample Serial Interface Parameters Group E Default SettingsParity Baud RateStop Bit General Selections Group BBeep Volume Code/Track IDScan Verification Enter one character for the new ID Code ID Definition GroupBar Code Terminator Character Bar Code Message Formatting Selections Group CBar Code Postamble Bar Code PreambleMagnetic Stripe Terminator Character Magnetic Stripe Formatting Selections Group DMagnetic Stripe Postamble Magnetic Stripe PreambleBar Code Selections Industrial Bar Codes Group FMinimum and Maximum Length Options Code 39 Settings Enable/Disable CodeFull Ascii Send Start/Stop Characters Interleaved 2 of 5 SettingsEnable/Disable Interleaved 2 Check DigitFixed Length Febraban ConversionEnable/Disable Industrial 2 Industrial 2 of 5 SettingsCode 128 Setting Enable/Disable Codabar Codabar SettingsEnable/Disable Telepen MSI/Plessey SettingsTelepen Setting Enable/Disable MSI/PlesseyUPC Settings Enable/Disable UPC-ARetail Bar Codes Group G UPC-E Expansion Enable/Disable UPC-ESend Number System Digit Send Check DigitAdd Separator Space Read Two-Digit AddendumRead Five-Digit Addendum Addendum RequiredSend Induced Country Code Character EAN SettingsEnable/Disable EAN-13 Enable/Disable EAN-8Read Five-Digit Addendum Do Not Read Five-Digit Addendum Magnetic Stripe Selections Group H Track SelectionSend Start/Stop Sentinel H4ENTERSELECTED Characterenter Reviewing Configuration SettingsTrack Two Send Accout Number Only Track SeparatorMSI Data Editing Data Fields Data Editing Formulas Code Idlengthmatchdivideaddsend Formula SequenceTrack 1 %CABREADOE$JANE$R$310 S Jefferson ST? Using the Data Editing FunctionsData Editing Commands Data Editing On/OffUnmatched Input Send/Do Not Send Select Code IDs Set LengthJDENTER0ENTER6ENTER1ENTER2ENTER JFENTER0ENTER7ENTER Match StringCreate a Data Field JEENTER0ENTER8ENTERAENTERBENTER CenterdentereenterSearch for a Data String Add a Data FieldJgenteraenterbentercenter Dentereenter Jkenteraentercenterbenter Time DelaySet the Sequence in which Data Fields are Sent Delete One FormulaOmni Data Flow Reset Data Editing GroupReview Configurations Exit Data Editing ModeExamples Symbology CodeJEENTER0ENTER7ENTER Send BD DLY 09 AD DLYJDENTER0ENTER7ENTER0 Enter 7ENTERMSR Track 1 data Operation Operating ProcedureGeneral Procedures TroubleshootingSerial Interface Problems Scanning Configurations Default Settings Appendix aCrlf Industrial Bar Codes Retail Barcodes UPC-A, -EUPC-A UPC-E EAN-8 Magnetic Stripe Format Appendix BMagnetic Stripe Standard Data Formats Appendix CCalifornia Driver’s License Format Track LRE ID Aamva Driver’s License Format Track Full Ascii Table Appendix DAscii Connector PIN-OUTS Appendix ERS-232 Port, Standard DB-9P Installing the Drivers Appendix FUSB/RS-232 Interface Page UE Anyway Checking the Installation and Modifying the COM Port Number Telling Whether the Installed Device is Type a or Type BTroubleshooting Date Driver Updating the DriverVersal Serial BUS Controllers Removing the DriverID Tech