MRV Communications TS700/G, TS700/155, TS800/155 TheProduct, Models Part Number Description

Page 11

M R V C o m m u n i c a t i o n s , I n c . – I n s t a l l a t i o n M a n u a l

Chapter

1

TheProduct

Caution!

When handling the TereScope, take special care not to damage the polycarbonate window!

Models

Table 1: Models of the TereScope1

Models

Part Number

Description

 

 

 

TS700/100

TS100/A/FET/VS

TereScope700 for Fast Ethernet

 

 

100Base-TX connectivity up to a distance

 

 

of 360 m + Power-over-Ethernet option.

 

 

 

TS700/155

TS155/A/YUW/VS

TereScope700 for 1-155 Mbps

 

 

connectivity up to a distance of 360 m.

 

 

 

TS700/G

TS1000/A/YUW/VS

TereScope700 for Gigabit Ethernet and

 

 

FiberChannel (1.0625) connectivity up to

 

 

a distance of 400 m

 

 

 

TS800/155

TS155/C2/YUW/VS

TereScope800 for 1-155 Mbps

 

 

connectivity up to a distance of 550 m +

 

 

Fusion option.

 

 

 

Using the Part Number for Ordering

To place an order for a TereScope model having a specific configuration, use the Part Number format shown in Table 1, noting the following:

‘155’ represents link operation speed in the range 1 to 155 Mbps. ‘A’ represents TereScope700.

‘C2’ represents TereScope800.

‘Y’ represents Optical Fiber Mode.

Instead of Y use one of the following: M (for MultiMode)

1TereScope700 or TereScope800.

1

Image 11
Contents UserManual UserManual TableofContents P E N D I CE Mark StandardsStandards Compliance FCC NoticeTrademarks MRV  Laser Safety CertificationOther Standards DisclaimerAboutthisUserManual Before Installing SafetyRequirementsServicing Introduction Carefully Read the Entire Manual Before InstallingModels Part Number Description Using the Part Number for OrderingTheProduct Front MRV Back Panel Description TS800/155 Standard Model DS1 Toggles Data Rate DIP switch TS800/155-F Standard Model including Fusion option RF Transceiver Fusion Operation Mode5b TS & Fusion FusionTS700/100 Fast-Ethernet System OFF Auto-negotiation, on Forced MRV Display LEDs,Dry Dry contact Only TS800 Monitoring and Management optionsManagement Copper Connection Typical ConnectionFiber Connection Location & Range SiteSurveyLine of Sight OrientationConsult Factory in Case of Doubt Optimal Mounting Unacceptable Mounting Mounting Environment & StabilityPage Transmitting through a Window Wall Mounting using JMP and JMB12 shows the arrangement for transmitting through a window Infrastructure PowerData/Signal Cabling Handle the Fibers Very Carefully Test equipment SetupBenchTest CompatibilityTS700/100Fastethernet IR link Bench testDisplay and Results IndicatorsExpected Results Received powerDescription InstallationAccessories TereScope Parts External view Part DescriptionAiming Head Adjustment and Locks Detachment of the TS from the JMP-L Installer Tool Kit JITK-LMounting Standard position a Mounting the accessoriesMounting on the floor Special MountingJMP-L Mounting on a fragile/crumbly wall17 Alignment kit mountedon JMP-L Back view Attachment of the Transceiver TereScope HeadPowering on the TereScope AimingProcedureTools and Equipment ProcedureTransceiver Alignment GeneralFine Alignment 13 Position after the horizontal aiming 15a and 6.15b Alignment screws Visual Inspection InstallationCompletionLink Operating Test Before Closing the Rear Door17 Mounted TereScope Left View Periodic Visits MaintenanceAccuracy should be examined and restored if necessary Appendix a TS700/100 Fast-Ethernet Light TS800/155 high speed Light TS700/G Giga-Light Appendixb Packing box contains AppendixcAppendixd List of the Tools Supplied by MRV Communications Where to usePoints to Remember IntroductionInterference Figure E.3 Active Transmitters Shown Darkened Page Appendixf Effect of Wind on Terescopes FSO Chaining AppendixGIndirect Chaining Use the indoor switch in building C for the chainingFSO products & Chaining Product series No of chained links Appendixh Site survey Installation System failure Appendixi