MRV Communications TS800/155, TS700/155, TS700/100 Standards Compliance, FCC Notice, CE Mark

Page 5

M R V C o m m u n i c a t i o n s , I n c . – I n s t a l l a t i o n M a n u a l

Standards

Standards Compliance

UL 1950; CSA 22.2 No 950; FCC Part 15 Class B; CE-89/336/EEC, 73/23/EEC

FCC Notice

WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions in the manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct for the interference at the user’s own expense.

The user is cautioned that changes and modifications made to the equipment without approval of the manufacturer could void the user’s authority to operate this equipment.

It is suggested that the user use only shielded and grounded cables when appropriate to ensure compliance with FCC Rules.

CE Mark

The CE mark symbolizes compliance with the EMC directive of the European Community. Such marking is indicative that the specified equipment meets or exceeds the following technical standards:

•EN 55022 - Limits and Methods of Measurement of Radio Interference Characteristics of Information Technology Equipment

•EN 50081-1- Electromagnetic compatibility - of Radio Interference Characteristics of Information Technology Equipment Generic Emission standard Part 1 – Residential commercial and light industry environment

•EN 50082-1 - Electromagnetic compatibility -- Generic immunity standard Part 1: Residential, commercial and light industry environment

•EN61000-4-2 (previously IEC 1000-4-2) - Electromagnetic compatibility for industrial- process measurement and control equipment Part 4: Section 2 - Electrostatic discharge requirements

•EN61000-4-3 (previously IEC 1000-4-3) - Electromagnetic compatibility for industrial- process measurement and control equipment Part 4: Section 3 - Radiated electromagnetic field requirements

•EN61000-4-4 (previously IEC 1000-4-4) - Electromagnetic compatibility for industrial- process measurement and control equipment Part 4: Section 4 - Electrical fast transient/burst requirements

•EN61000-4-5 - Electromagnetic compatibility for industrial-process measurement and control equipment

Part 4: Section 5 – Surge Immunity requirements

•EN61000-4-6 - Electromagnetic compatibility for industrial-process measurement and control equipment

Part 4: Section 6 – Immunity to conducted disturbances induces by radio frequency fields

•EN61000-4-8- Electromagnetic compatibility for industrial-process measurement and control equipment

Part 4: Section 8– Power frequency magnetic field immunity requirements

•EN61000-4-11 – Electromagnetic compatibility for industrial-process measurement and control equipment Part 4: Section 11 – Voltage dips short interruptions and voltage variations immunity requirements

•EN61000-3-2 – Harmonic standard

•EN61000-3-3 – Voltage Fluctuation and Flicker standard

•CISPR 22 - Radiated and Line-conducted Class B

•EN 60950 - ITE Safety

i

Page 4 Page 6
Image 5
Page 4 Page 6
Contents UserManual UserManual TableofContents P E N D I Standards Compliance StandardsFCC Notice CE MarkOther Standards MRV  Laser Safety CertificationDisclaimer TrademarksAboutthisUserManual Before Installing SafetyRequirementsServicing Introduction Carefully Read the Entire Manual Before InstallingModels Part Number Description Using the Part Number for OrderingTheProduct Front MRV Back Panel Description TS800/155 Standard Model DS1 Toggles Data Rate DIP switch TS800/155-F Standard Model including Fusion option RF Transceiver Fusion Operation Mode5b TS & Fusion FusionTS700/100 Fast-Ethernet System OFF Auto-negotiation, on Forced MRV Display LEDs,Dry Dry contact Only TS800 Monitoring and Management optionsManagement Copper Connection Typical ConnectionFiber Connection Line of Sight SiteSurveyOrientation Location & RangeConsult Factory in Case of Doubt Optimal Mounting Unacceptable Mounting Mounting Environment & StabilityPage Transmitting through a Window Wall Mounting using JMP and JMB12 shows the arrangement for transmitting through a window Infrastructure PowerData/Signal Cabling Handle the Fibers Very Carefully BenchTest SetupCompatibility Test equipmentTS700/100Fastethernet IR link Bench testDisplay and Results IndicatorsExpected Results Received powerDescription InstallationAccessories TereScope Parts External view Part DescriptionAiming Head Adjustment and Locks Detachment of the TS from the JMP-L Installer Tool Kit JITK-LMounting Standard position a Mounting the accessoriesMounting on the floor Special MountingJMP-L Mounting on a fragile/crumbly wall17 Alignment kit mountedon JMP-L Back view Attachment of the Transceiver TereScope HeadPowering on the TereScope AimingProcedureTransceiver Alignment ProcedureGeneral Tools and EquipmentFine Alignment 13 Position after the horizontal aiming 15a and 6.15b Alignment screws Link Operating Test InstallationCompletionBefore Closing the Rear Door Visual Inspection17 Mounted TereScope Left View Periodic Visits MaintenanceAccuracy should be examined and restored if necessary Appendix a TS700/100 Fast-Ethernet Light TS800/155 high speed Light TS700/G Giga-Light Appendixb Packing box contains AppendixcAppendixd List of the Tools Supplied by MRV Communications Where to usePoints to Remember IntroductionInterference Figure E.3 Active Transmitters Shown Darkened Page Appendixf Effect of Wind on Terescopes FSO Chaining AppendixGIndirect Chaining Use the indoor switch in building C for the chainingFSO products & Chaining Product series No of chained links Appendixh Site survey Installation System failure Appendixi
Top Page Image Contents