MRV Communications TS700/155, TS800/155, TS700/100, TS700/G user manual Display LEDs,Dry

Page 24

M R V C o m m u n i c a t i o n s , I n c . – I n s t a l l a t i o n M a n u a l

Selectors

Transmitter Mode

ON position (up) for links above 150m distance.

 

(DIP Switch

(Toggle 1)

OFF position (down) is for under 170m distance

 

Toggles)--

 

 

 

 

shown in Figure

Not Used

Not used.

 

1.7

(Toggle 2)

(No internal loopback function. For a complete

 

 

 

loop test, far-end loopback of airlink data can be

 

 

 

performed externally with fiber from Tx to Rx)

 

 

 

 

 

 

IP Address

When the Switch toggle is on OFF position, the

 

(Toggle 3)

TereScope’s IP address is the default one (shown on

 

 

 

the back panel label: 10.0.0.101). To set a new IP

 

 

 

address please refer to the “IP address setting

 

 

 

procedure for TereScope management card” file in

 

 

 

the Manuals CD. The new IP address is valid only

 

 

 

after the TereScope is powered off and on.

 

 

 

 

 

 

Data rate

ON position (up) for Gigabit Ethernet,

 

(Toggle 4)

OFF position (down) for 1.0625Gb/s FiberChannel

 

 

 

 

 

 

 

 

 

 

 

Indicators

Air RX Flag LED

 

Green LED indicates signal received by the Airlink

(7-segment

 

 

receiver. Turns ON at the threshold level.

display,

 

 

 

 

LEDs),Dry

Laser Enabled LED

 

Red LED. Turns ON to indicate that laser in

Contact

 

 

enabled to transmit light.

Alarms

 

 

 

 

 

F/O RX Flag LED

 

Green LED indicates Data received by the Fiber

 

 

 

Optic receiver. Turns ON at the threshold level.

 

 

 

 

 

 

Pins 1,2

 

Closed (25 ohm) = Internal DC power functional

 

 

 

Open = internal DC voltage not present in circuit

 

 

 

 

 

 

Pins 3,4

 

Air Rx alarm

 

 

 

Closed (25 ohm) = airlink optical power received

 

 

 

above threshold

 

 

 

Open = received optical signal below threshold

 

 

 

 

 

 

Pins 5,6

 

F/O Rx alarm

 

 

 

Closed (25 ohm) = received signal at fiber interface

 

 

 

above threshold

 

 

 

open = signal received at fiber receiver below

 

 

 

threshold

 

 

 

 

 

 

Pins 7,8

 

Laser Enabled Alarm

 

 

 

Closed (25 ohm) laser is enabled

 

 

 

Open = laser is disabled due to malfunction

 

 

 

 

 

 

Optical Power 7-

 

Digital readout indicates the Optical Power level

 

segment display

 

received by the Airlink receiver.

 

 

 

 

 

Alignment

Telescope

For fine alignment.

14

Image 24
Contents UserManual UserManual TableofContents P E N D I Standards Standards ComplianceFCC Notice CE MarkMRV  Laser Safety Certification Other StandardsDisclaimer TrademarksAboutthisUserManual SafetyRequirements Before InstallingServicing Carefully Read the Entire Manual Before Installing IntroductionUsing the Part Number for Ordering TheProductModels Part Number Description Front MRV Back Panel Description TS800/155 Standard Model DS1 Toggles Data Rate DIP switch TS800/155-F Standard Model including Fusion option Fusion Operation Mode RF TransceiverFusion 5b TS & FusionTS700/100 Fast-Ethernet System OFF Auto-negotiation, on Forced MRV Display LEDs,Dry Monitoring and Management options ManagementDry contact Only TS800 Typical Connection Fiber ConnectionCopper Connection SiteSurvey Line of SightOrientation Location & RangeConsult Factory in Case of Doubt Optimal Mounting Mounting Environment & Stability Unacceptable MountingPage Wall Mounting using JMP and JMB Transmitting through a Window12 shows the arrangement for transmitting through a window Power Data/Signal CablingInfrastructure Handle the Fibers Very Carefully Setup BenchTestCompatibility Test equipmentTS700/100Fastethernet Bench test IR linkIndicators Display and ResultsReceived power Expected ResultsInstallation AccessoriesDescription Part Description TereScope Parts External viewAiming Head Adjustment and Locks Installer Tool Kit JITK-L MountingDetachment of the TS from the JMP-L Mounting the accessories Standard position aSpecial Mounting Mounting on the floorMounting on a fragile/crumbly wall JMP-LAttachment of the Transceiver TereScope Head 17 Alignment kit mountedon JMP-L Back viewAimingProcedure Powering on the TereScopeProcedure Transceiver AlignmentGeneral Tools and EquipmentFine Alignment 13 Position after the horizontal aiming 15a and 6.15b Alignment screws InstallationCompletion Link Operating TestBefore Closing the Rear Door Visual Inspection17 Mounted TereScope Left View Maintenance Accuracy should be examined and restored if necessaryPeriodic Visits Appendix a TS700/100 Fast-Ethernet Light TS800/155 high speed Light TS700/G Giga-Light Appendixb Appendixc Packing box containsAppendixd Where to use List of the Tools Supplied by MRV CommunicationsIntroduction Points to RememberInterference Figure E.3 Active Transmitters Shown Darkened Page Appendixf Effect of Wind on Terescopes AppendixG FSO ChainingUse the indoor switch in building C for the chaining Indirect ChainingFSO products & Chaining Product series No of chained links Appendixh Site survey Installation System failure Appendixi