MRV Communications TS700/100, TS700/155, TS800/155, TS700/G Special Mounting, Mounting on the floor

Page 46
JMP-L
M8 (25mm)* 6places

M R V C o m m u n i c a t i o n s , I n c . – I n s t a l l a t i o n M a n u a l

Figure 5.13b: JMP-L on the fixation surface

THE JMP-L SHOULD BE ORIENTED IN SUCH A WAY THAT THE GROUNDING SCREW IS LOCATED ON THE BACK (CLOSE TO THE INSTALLER) AND THE FRONT FACING THE OPPOSITE SITE.

)Vertical surfaces (wall, rectangular column, ...):

Use a JMB (To be ordered separately, not included in the standard kit)

&

*These bolts and nuts are included in the kit

JMB Left

JMB Right

Figure 5.14: JMP-L on JMB

Note

For more convenience it is suggested to assemble the 3 parts of the JMB before mounting it on the surface.

Special Mounting

1- Mounting on the floor

In some cases the only place where the installation is acceptable, possible, or authorized is on the floor. Avoid installation on roofs with a metallic parapet or without a parapet by drilling holes in the roof floor.

36

Image 46
Contents UserManual UserManual TableofContents P E N D I FCC Notice StandardsStandards Compliance CE MarkDisclaimer MRV  Laser Safety CertificationOther Standards TrademarksAboutthisUserManual SafetyRequirements Before InstallingServicing Carefully Read the Entire Manual Before Installing IntroductionTheProduct Using the Part Number for OrderingModels Part Number Description Front MRV Back Panel Description TS800/155 Standard Model DS1 Toggles Data Rate DIP switch TS800/155-F Standard Model including Fusion option Fusion Operation Mode RF TransceiverFusion 5b TS & FusionTS700/100 Fast-Ethernet System OFF Auto-negotiation, on Forced MRV Display LEDs,Dry Management Monitoring and Management optionsDry contact Only TS800 Fiber Connection Typical ConnectionCopper Connection Orientation SiteSurveyLine of Sight Location & RangeConsult Factory in Case of Doubt Optimal Mounting Mounting Environment & Stability Unacceptable MountingPage Wall Mounting using JMP and JMB Transmitting through a Window12 shows the arrangement for transmitting through a window Data/Signal Cabling PowerInfrastructure Handle the Fibers Very Carefully Compatibility SetupBenchTest Test equipmentTS700/100Fastethernet Bench test IR linkIndicators Display and ResultsReceived power Expected ResultsAccessories InstallationDescription Part Description TereScope Parts External viewAiming Head Adjustment and Locks Mounting Installer Tool Kit JITK-LDetachment of the TS from the JMP-L Mounting the accessories Standard position aSpecial Mounting Mounting on the floorMounting on a fragile/crumbly wall JMP-LAttachment of the Transceiver TereScope Head 17 Alignment kit mountedon JMP-L Back viewAimingProcedure Powering on the TereScopeGeneral ProcedureTransceiver Alignment Tools and EquipmentFine Alignment 13 Position after the horizontal aiming 15a and 6.15b Alignment screws Before Closing the Rear Door InstallationCompletionLink Operating Test Visual Inspection17 Mounted TereScope Left View Accuracy should be examined and restored if necessary MaintenancePeriodic Visits Appendix a TS700/100 Fast-Ethernet Light TS800/155 high speed Light TS700/G Giga-Light Appendixb Appendixc Packing box containsAppendixd Where to use List of the Tools Supplied by MRV CommunicationsIntroduction Points to RememberInterference Figure E.3 Active Transmitters Shown Darkened Page Appendixf Effect of Wind on Terescopes AppendixG FSO ChainingUse the indoor switch in building C for the chaining Indirect ChainingFSO products & Chaining Product series No of chained links Appendixh Site survey Installation System failure Appendixi