MRV Communications TS700/100 Other Standards, MRV  Laser Safety Certification, Disclaimer

Page 6

M R V C o m m u n i c a t i o n s , I n c . – I n s t a l l a t i o n M a n u a l

Other Standards

1. CISPR 22: 1993

AS/NZS 3548: 1995, Class B

Joint Amendment No. 1: 1997, Joint Amendment No. 2: 1997

2.EN 60950+A1+A2+A3+A4+A11 ACA TS001-1997

AS/NZS 3260: 1993 A4: 1997

3.ITU G.703, G.704, G.706,G.736, G.737, G.738, G739, G740, G.775, G.823.

MRV Laser Safety Certification

The TereScope is designed, built, and tested to be eyesafe, even if the output beams are viewed directly, provided that no magnifying optics are used.

This product is Class 1M according to the American National Standard for Safe Use of Lasers, ANSI Z136.1-1993, provided that there is not a reasonable probability of accidental viewing with optics in the direct path of the beam where the TereScope is installed.

This product is Class 1M according to the International Standard of the International Electrotechnical Commision IEC 60825-1, Amendment 2, January 2001 entitled “Safety of laser products.” The following explanatory label is applicable to these products:

LASER RADIATION

DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS

(BINOCULARS OR TELESCOPES)

CLASS 1M LASER PRODUCT

This product complies with United States FDA performance standards for laser products except for deviations pursuant to Laser Notice No. 50 as published in June, 2001, which allows for the use of the IEC 60825-1 classification standard. Under this standard, these products are Class 1M.

A ‘Declaration of Conformity’, in accordance with the above standards, has been made and is on file at MRV.

Disclaimer

MRV reserves the right to modify the equipment at any time and in any way it sees fit in order to improve it.

MRV provides this document without any warranty of any kind, either expressed or implied, including, but not limited to, the implied warranties of merchantability or fitness for a particular purpose.

The customer is advised to exercise due discretion in the use of the contents of this document since the customer bears sole responsibility.

Trademarks

All trademarks are the property of their respective holders.

Copyright © 2004 by MRV

All rights reserved. No part of this document may be reproduced without the prior permission of MRV.

This document and the information contained herein are proprietary to MRV and are furnished to the recipient solely for use in operating, maintaining and repairing MRV equipment. The information within may not be utilized for any purpose except as stated herein, and may not be disclosed to third parties without written permission from MRV. MRV reserves the right to make changes to any technical specifications in order to improve reliability, function, or design.

ii

Image 6
Contents UserManual UserManual TableofContents P E N D I FCC Notice StandardsStandards Compliance CE MarkDisclaimer MRV  Laser Safety CertificationOther Standards TrademarksAboutthisUserManual SafetyRequirements Before InstallingServicing Carefully Read the Entire Manual Before Installing IntroductionUsing the Part Number for Ordering TheProductModels Part Number Description Front MRV Back Panel Description TS800/155 Standard Model DS1 Toggles Data Rate DIP switch TS800/155-F Standard Model including Fusion option Fusion Operation Mode RF TransceiverFusion 5b TS & FusionTS700/100 Fast-Ethernet System OFF Auto-negotiation, on Forced MRV Display LEDs,Dry Monitoring and Management options ManagementDry contact Only TS800 Typical Connection Fiber ConnectionCopper Connection Orientation SiteSurveyLine of Sight Location & RangeConsult Factory in Case of Doubt Optimal Mounting Mounting Environment & Stability Unacceptable MountingPage Wall Mounting using JMP and JMB Transmitting through a Window12 shows the arrangement for transmitting through a window Power Data/Signal CablingInfrastructure Handle the Fibers Very Carefully Compatibility SetupBenchTest Test equipmentTS700/100Fastethernet Bench test IR linkIndicators Display and ResultsReceived power Expected ResultsInstallation AccessoriesDescription Part Description TereScope Parts External viewAiming Head Adjustment and Locks Installer Tool Kit JITK-L MountingDetachment of the TS from the JMP-L Mounting the accessories Standard position aSpecial Mounting Mounting on the floorMounting on a fragile/crumbly wall JMP-LAttachment of the Transceiver TereScope Head 17 Alignment kit mountedon JMP-L Back viewAimingProcedure Powering on the TereScopeGeneral ProcedureTransceiver Alignment Tools and EquipmentFine Alignment 13 Position after the horizontal aiming 15a and 6.15b Alignment screws Before Closing the Rear Door InstallationCompletionLink Operating Test Visual Inspection17 Mounted TereScope Left View Maintenance Accuracy should be examined and restored if necessaryPeriodic Visits Appendix a TS700/100 Fast-Ethernet Light TS800/155 high speed Light TS700/G Giga-Light Appendixb Appendixc Packing box containsAppendixd Where to use List of the Tools Supplied by MRV CommunicationsIntroduction Points to RememberInterference Figure E.3 Active Transmitters Shown Darkened Page Appendixf Effect of Wind on Terescopes AppendixG FSO ChainingUse the indoor switch in building C for the chaining Indirect ChainingFSO products & Chaining Product series No of chained links Appendixh Site survey Installation System failure Appendixi