MRV Communications TS800/155, TS700/155, TS700/G user manual TS700/100 Fast-Ethernet System

Page 21

M R V C o m m u n i c a t i o n s , I n c . – I n s t a l l a t i o n M a n u a l

D. TS700/100 - Fast-Ethernet System

Figure 1.6: TS700/100 Model Back Panel

Back Panel Description

Table 4: TS700/100 Back Panel Controls, Interfaces, and Indicators

Connectors

 

Power

 

Power source Terminal Block (Main or UPS)

 

 

 

AC power supply (100 to 240 Vac) or DC power

 

 

 

supply (24 to 60 Vdc).

 

 

 

 

 

100Base-TX

 

Copper interface (RJ45) for STP cables.

 

 

 

MDI-X connection (TX: pins 3,6 and RX: pins 1,2).

 

 

 

Connection to the peripheral equipment.

 

 

 

This connector can be used for Power-over-Ethernet

 

 

 

(PoE) but only with the Low Voltage TereScope version

 

 

 

(TS100/A/FET/V3). The standard power for PoE is

 

 

 

36-57 Vdc. However, the TS700/100 can operate with

 

 

 

20-60 Vdc.

 

 

 

See appendix I.

 

 

 

 

 

Management

 

Connection to 10Base-T SNMP management

 

(Optional)

 

interface. (To be ordered separately)

 

 

 

 

 

Dry Contacts

 

There are 2 pairs of dry contact indicators available,

 

 

 

one for Air RX Link LED (Pins 1 and 2), and the

 

 

 

other for 100BaseT LED (Pins 3 and for). Dry

 

 

 

contacts are normally closed (25 ohms), and open in

 

 

 

an alarm condition

 

 

 

 

11

Image 21
Contents UserManual UserManual TableofContents P E N D I Standards Compliance StandardsFCC Notice CE MarkOther Standards MRV  Laser Safety CertificationDisclaimer TrademarksAboutthisUserManual Before Installing SafetyRequirementsServicing Introduction Carefully Read the Entire Manual Before InstallingUsing the Part Number for Ordering TheProductModels Part Number Description Front MRV Back Panel Description TS800/155 Standard Model DS1 Toggles Data Rate DIP switch TS800/155-F Standard Model including Fusion option RF Transceiver Fusion Operation Mode5b TS & Fusion FusionTS700/100 Fast-Ethernet System OFF Auto-negotiation, on Forced MRV Display LEDs,Dry Monitoring and Management options ManagementDry contact Only TS800 Typical Connection Fiber ConnectionCopper Connection Line of Sight SiteSurveyOrientation Location & RangeConsult Factory in Case of Doubt Optimal Mounting Unacceptable Mounting Mounting Environment & StabilityPage Transmitting through a Window Wall Mounting using JMP and JMB12 shows the arrangement for transmitting through a window Power Data/Signal CablingInfrastructure Handle the Fibers Very Carefully BenchTest SetupCompatibility Test equipmentTS700/100Fastethernet IR link Bench testDisplay and Results IndicatorsExpected Results Received powerInstallation AccessoriesDescription TereScope Parts External view Part DescriptionAiming Head Adjustment and Locks Installer Tool Kit JITK-L MountingDetachment of the TS from the JMP-L Standard position a Mounting the accessoriesMounting on the floor Special MountingJMP-L Mounting on a fragile/crumbly wall17 Alignment kit mountedon JMP-L Back view Attachment of the Transceiver TereScope HeadPowering on the TereScope AimingProcedureTransceiver Alignment ProcedureGeneral Tools and EquipmentFine Alignment 13 Position after the horizontal aiming 15a and 6.15b Alignment screws Link Operating Test InstallationCompletionBefore Closing the Rear Door Visual Inspection17 Mounted TereScope Left View Maintenance Accuracy should be examined and restored if necessaryPeriodic Visits Appendix a TS700/100 Fast-Ethernet Light TS800/155 high speed Light TS700/G Giga-Light Appendixb Packing box contains AppendixcAppendixd List of the Tools Supplied by MRV Communications Where to usePoints to Remember IntroductionInterference Figure E.3 Active Transmitters Shown Darkened Page Appendixf Effect of Wind on Terescopes FSO Chaining AppendixGIndirect Chaining Use the indoor switch in building C for the chainingFSO products & Chaining Product series No of chained links Appendixh Site survey Installation System failure Appendixi