MRV Communications TS700/155, TS800/155, TS700/100, TS700/G SafetyRequirements, Before Installing

Page 8

M R V C o m m u n i c a t i o n s , I n c . – I n s t a l l a t i o n M a n u a l

SafetyRequirements

All requirements stipulated in the safety laws of the country of installation must be abided by when installing the TereScopes.

Caution!

In addition, ensure that the requirements noted in this chapter are met in order to reduce risk of electrical shock and fire and to maintain proper operation.

Figure A: 3 terminal cord forks

Before Installing

Power: Ensure that all power to the TereScope is cut off. Specifically, disconnect all TereScope power cords from the power line (mains). Inspection: Ensure by inspection that no part is damaged.

Before Powering On

Line Power: Ensure that the power from the line (mains) is as specified on the TereScope.

Power Cord: The power cord of The TereScope must have the following specifications:

Flexible 3-conductor power cord approved by the cognizant safety organization of the country. The power cord must be Type HAR (harmonized), with individual conductor wire having cross-sectional area 0.75 sq. mm. min. The power cord terminations should be a suitably rated earthing-type plug at one end and 3 terminal cord forks for M3 screws (1 for each wire) at the other end. Both of the power cord terminations must carry the certification label of the cognizant safety organization of the country.

When Installing

•Ensure, by visual inspection, that no part of the TereScope is damaged.

•Avoid eye contact with the laser beam at all times.

•Ensure that the system is installed in accordance with ANSI Z136.1 control measures (engineering, administrative, and procedural controls).

•Ensure that the system is installed in accordance with applicable building and installations codes.

•Install the TereScope in a restricted location as defined in this manual since it is a Class 1M FSOCS transmitter and receiver. A restricted location is a location where access to the transmission equipment and exposed beam is restricted and not accessible to the general public or

iv

Image 8

Contents UserManual UserManual TableofContents P E N D I Standards Standards ComplianceFCC Notice CE MarkMRV  Laser Safety Certification Other StandardsDisclaimer TrademarksAboutthisUserManual SafetyRequirements Before InstallingServicing Carefully Read the Entire Manual Before Installing IntroductionModels Part Number Description Using the Part Number for OrderingTheProduct Front MRV Back Panel Description TS800/155 Standard Model DS1 Toggles Data Rate DIP switch TS800/155-F Standard Model including Fusion option Fusion Operation Mode RF TransceiverFusion 5b TS & FusionTS700/100 Fast-Ethernet System OFF Auto-negotiation, on Forced MRV Display LEDs,Dry Dry contact Only TS800 Monitoring and Management optionsManagement Copper Connection Typical ConnectionFiber Connection SiteSurvey Line of SightOrientation Location & RangeConsult Factory in Case of Doubt Optimal Mounting Mounting Environment & Stability Unacceptable MountingPage Wall Mounting using JMP and JMB Transmitting through a Window12 shows the arrangement for transmitting through a window Infrastructure PowerData/Signal Cabling Handle the Fibers Very Carefully Setup BenchTestCompatibility Test equipmentTS700/100Fastethernet Bench test IR linkIndicators Display and ResultsReceived power Expected ResultsDescription InstallationAccessories Part Description TereScope Parts External viewAiming Head Adjustment and Locks Detachment of the TS from the JMP-L Installer Tool Kit JITK-LMounting Mounting the accessories Standard position aSpecial Mounting Mounting on the floorMounting on a fragile/crumbly wall JMP-LAttachment of the Transceiver TereScope Head 17 Alignment kit mountedon JMP-L Back viewAimingProcedure Powering on the TereScopeProcedure Transceiver AlignmentGeneral Tools and EquipmentFine Alignment 13 Position after the horizontal aiming 15a and 6.15b Alignment screws InstallationCompletion Link Operating TestBefore Closing the Rear Door Visual Inspection17 Mounted TereScope Left View Periodic Visits MaintenanceAccuracy should be examined and restored if necessary Appendix a TS700/100 Fast-Ethernet Light TS800/155 high speed Light TS700/G Giga-Light Appendixb Appendixc Packing box containsAppendixd Where to use List of the Tools Supplied by MRV CommunicationsIntroduction Points to RememberInterference Figure E.3 Active Transmitters Shown Darkened Page Appendixf Effect of Wind on Terescopes AppendixG FSO ChainingUse the indoor switch in building C for the chaining Indirect ChainingFSO products & Chaining Product series No of chained links Appendixh Site survey Installation System failure Appendixi