MRV Communications TS700/155, TS800/155, TS700/100, TS700/G user manual DS1 Toggles

Page 16

M R V C o m m u n i c a t i o n s , I n c . – I n s t a l l a t i o n M a n u a l

Selectors

Data Rate

Set the transmission rate of the transceiver (internal

(DIP Switch

(Toggles 1,2,3,4)

clock).

DS1 Toggles)

 

- Fast Ethernet: 1,2,3,4 OFF

-- shown in

 

- ATM/OC3/STM1:155 Mbps: 2,3,4 OFF, 1 ON

Figure 1.3and

 

- SMPTE 143 Mbps: 3,4 OFF, 1,2 ON

1.4

 

- E3: 34.368 Mbps1,2,4 OFF, 3 ON

 

 

- T3: 44.736 Mbps: 2,4 OFF, 1,3 ON

 

 

- OC1/STM0: 51.840 Mbps: 1,4 OFF, 2,3 ON

 

 

- Customized 1 : 4 OFF, 1,2,3 ON

 

 

- Customized 2 : 1,3,4 OFF, 2 ON

 

 

- Open Protocol: 1,2,3 OFF, 4 ON.

Selectors

Mode Select

Set the Operating Mode

(DIP Switch

(Toggles 1, 2, 3)

ALIGNMENT = Idle transmitted automatically

DS2 Toggles)

 

NORMAL = Signal received via the F/O port is

-- shown in

 

transmitted through the Airlink TX. Signal received

Figure 1.3 and

 

via the Airlink RX is transmitted through the F/O

1.4

 

TX.

 

 

LOOPBACK= Data received by the F/O RX is

 

 

directly returned through the F/O TX.

 

 

REMOTE LOOP = Loops the electrical RX to the

 

 

electrical TX and optical RX to the optical TX of the

 

 

remote unit.

 

 

ATTENUATION: The alignment signal is

 

 

attenuated (~20db) when the DIP switch toggle #3

 

 

is moved to ON position.(to use when the

 

 

installation distance is less than 200m only for

 

 

alignment mode). Switch back to OFF position for

 

 

normal mode.

 

Laser Power Off

Turning off laser TX when the DIP switch toggle is

 

(Toggle 4)

moved to ON

 

Fusion

This switch toggle enables working with MRV’s

 

(Toggle 5)

Fusion system (Built-in fusion option or switch

 

 

option). For additional information, see page 7.

 

 

Switch toggle 5 OFF: Fusion not Active (Disabled)

 

 

Switch toggle 5 ON: Fusion active (Enabled).

 

Window Heater

Used only with the heating option (To be specified

 

(Optional)

in the PO).

 

(Toggle 6)

Switch toggle 6 OFF: The heater is disabled

 

 

Switch toggle 5 ON: The heater is enabled.

 

IP address set up

When the Switch toggle is on OFF position, the

 

(Toggle 7)

TereScope’s IP address is the default one (shown on

 

 

the back panel label: 10.0.0.101). To set a new IP

 

 

address please refer to the “IP address setting

 

 

procedure for TereScope management card” file in

 

 

the Manuals CD. The new IP address is valid only

 

 

after the TereScope is powered off and on.

 

Control Mode

When the Dip Switch toggle #8 is on OFF position,

 

(Toggle 8)

the TereScope is in the HARDWARE mode, i.e. the

 

 

TereScope is controlled only by the TereScope itself

 

 

by means of the switches on its back panel.

 

 

When the Dip Switch toggle is on ON position, the

 

 

TereScope is in the SOFTWARE mode i.e. the

 

 

TereScope is controlled by the management

 

 

Software and various functions can be activated by

 

 

means of this management Software.

 

 

 

Note: Pins (4,5) and (7,8) of the management RJ45 connector can be used for dry contact purposes, for Airlink flag and F/O flag alarms respectively.

6

Image 16
Contents UserManual UserManual TableofContents P E N D I Standards Standards ComplianceFCC Notice CE MarkMRV  Laser Safety Certification Other StandardsDisclaimer TrademarksAboutthisUserManual SafetyRequirements Before InstallingServicing Carefully Read the Entire Manual Before Installing IntroductionTheProduct Using the Part Number for OrderingModels Part Number Description Front MRV Back Panel Description TS800/155 Standard Model DS1 Toggles Data Rate DIP switch TS800/155-F Standard Model including Fusion option Fusion Operation Mode RF TransceiverFusion 5b TS & FusionTS700/100 Fast-Ethernet System OFF Auto-negotiation, on Forced MRV Display LEDs,Dry Management Monitoring and Management optionsDry contact Only TS800 Fiber Connection Typical ConnectionCopper Connection SiteSurvey Line of SightOrientation Location & RangeConsult Factory in Case of Doubt Optimal Mounting Mounting Environment & Stability Unacceptable MountingPage Wall Mounting using JMP and JMB Transmitting through a Window12 shows the arrangement for transmitting through a window Data/Signal Cabling PowerInfrastructure Handle the Fibers Very Carefully Setup BenchTestCompatibility Test equipmentTS700/100Fastethernet Bench test IR linkIndicators Display and ResultsReceived power Expected ResultsAccessories InstallationDescription Part Description TereScope Parts External viewAiming Head Adjustment and Locks Mounting Installer Tool Kit JITK-LDetachment of the TS from the JMP-L Mounting the accessories Standard position aSpecial Mounting Mounting on the floorMounting on a fragile/crumbly wall JMP-LAttachment of the Transceiver TereScope Head 17 Alignment kit mountedon JMP-L Back viewAimingProcedure Powering on the TereScopeProcedure Transceiver AlignmentGeneral Tools and EquipmentFine Alignment 13 Position after the horizontal aiming 15a and 6.15b Alignment screws InstallationCompletion Link Operating TestBefore Closing the Rear Door Visual Inspection17 Mounted TereScope Left View Accuracy should be examined and restored if necessary MaintenancePeriodic Visits Appendix a TS700/100 Fast-Ethernet Light TS800/155 high speed Light TS700/G Giga-Light Appendixb Appendixc Packing box containsAppendixd Where to use List of the Tools Supplied by MRV CommunicationsIntroduction Points to RememberInterference Figure E.3 Active Transmitters Shown Darkened Page Appendixf Effect of Wind on Terescopes AppendixG FSO ChainingUse the indoor switch in building C for the chaining Indirect ChainingFSO products & Chaining Product series No of chained links Appendixh Site survey Installation System failure Appendixi