Multi-Tech Systems BA-Series manual Multi-Tech Result Codes, Standard AT Result Codes

Page 26

MultiModemBA User Guide

4.3Result Codes

The Command mode provides you with several responses, or “Result Codes”, that can aid you in Command mode operation. These Result Codes are displayed on your video monitor.

You can choose result codes that closely match those of the standard AT command set, or choose enhanced function result codes that have been used in Multi-Tech modems ("Multi-Tech"responses). The &Q command selects which result codes will be used.

You can choose to have these Result Codes displayed in either “verbose” (full words) or “terse” (digits) format. This is controlled by the ATV0 (terse) or ATV1 (verbose) commands. The modem defaults to verbose format.

AT&Q0 selects Multi-Tech responses with Reliable/LAPM/Compression modifiers. The terse response code for CONNECT 2400 is 9. AT&Q1 selects Standard AT command set responses. The terse result code for CONNECT 2400 is 10.

The following tables define the result codes generated by the &Q command (refer to Appendix G for Result Code Summary).

"Multi-Tech" Result Codes

TERSE	VERBOSE	TERSE	VERBOSE
0	OK	11*	CONNECT 4800
1	CONNECT	12*	CONNECT 9600
2	RING	13*	CONNECT 14400
3	NO CARRIER	19*	CONNECT 19200
4	ERROR	21*	CONNECT 21600
5*	CONNECT 1200	24*	CONNECT 24000
6	NO DIALTONE	26*	CONNECT 26400
7	BUSY	28*	CONNECT 28800
8	NO ANSWER	31*	CONNECT 31200
9*	CONNECT 2400	33*	CONNECT 33600

*With MNP error correction on, RELIABLE (or R) is added to these result codes. With LAP-M error correction on, LAP-M (or L) is added to these result codes. With data compression on, COMPRESSED (or C) is added. (Note these "Extended" Result Codes are displayed when your modem is set up to do so with an X1, X2, X3, or X4 command.)

"Standard AT" Result Codes
TERSE	VERBOSE	TERSE	VERBOSE
0	OK	11	CONNECT 4800
1	CONNECT	12	CONNECT 9600
2	RING	13	CONNECT 14400
3	NO CARRIER	19	CONNECT 19200
4	ERROR	21	CONNECT 21600
5	CONNECT 1200	24	CONNECT 24000
6	NO DIALTONE	26	CONNECT 26400
7	BUSY	28	CONNECT 28800
8	NO ANSWER	31	CONNECT 31200
10	CONNECT 2400	33	CONNECT 33600

*Reliable/Compression modifiers are not displayed with Standard AT Result Codes.

26

Image 26

Contents User Guide User Guide Record of RevisionsContents Index 106 Introduction and Description How To Use This Manual IntroductionDIP-Switches Modem FeaturesCallback and Remote Configuration Warranty, Service & Technical Support1 2834 Series Features Fax FeaturesTechnical Specifications Power Modem LED Indicators MT2834 LED DisplayControls on PC Board Installation and Connection What is in Your Modem Package? InstallationInstallation and Connection Safety WarningsInstallation Procedure Step ProcedureInstalling Data Communications Software MultiModemBA/BAI ConnectionsSoftware Configuration and Modem Basics PC Initialization Strings Configuring Your SoftwareConfiguring Software for Your Modem AT &F X4 S0=0 MConfiguring Software for the Remote System Changing Default ParametersConfiguring Software for Your Computer Other ParametersTerminal Emulation File Transfer ProtocolsCommand Mode AT Command Editing Functional ModesSummary of AT Commands Command ModeStore Modem Configure Data Standard AT Result Codes Result CodesMulti-Tech Result Codes Continuous Redial not used in BAI a or Dialing Commands Dialing Action CommandsDial Command D Dialing a Stored Number NVoice/Data Dialing $VD Dial Modifier CommandsDTR Dialing $D Pulse or Tone Dial P TSet Pulse Dial Ratios &P Return to Command Mode After Dial Command ExecutionReverse the Mode of Operation R Automatic Pauses in DialingCalling Card Detect Tones $ Phone Number Memory CommandsFlash On Hook Quiet Answer @Listing Numbers Stored in Memory L Configuration and Default Storage CommandsNumber Linking NN Async/Sync Mode Switching &M Loading Factory Defaults &FModem Reset Z Unix Uucp Spoofing $SPResult Codes Enable/Disable and No Response Answer Q Command Response Result Code CommandsEcho Command Mode Characters E Result Codes Multi-Tech or Standard AT &QGuard Tones Not Used in BAI Models &G Phone Line Conditioning CommandsResult Codes Basic and Extended and Call Progress Selection Bell/V.21 Tone Enable/Disable Trelis Coded Modulation #TFallback Modes When On-Line #F Phone Line Monitoring Speaker MCleardown at Disconnect &CD 7 RS-232C Interface Control CommandsEnable/Disable Lowspeed Fast Connect $FC Auto Speed Detect #AData Set Ready Control &S Data Terminal Ready Control &DCTS Control &R CTS/RTS Interaction Control &RFError Correction Commands Enable/Disable Auto Reliable Fallback Character $F Auto-Reliable Buffering $ARetransmit Count $R Flow Control CommandsError Correction/300bps $E Xon/Xoff Pass-Through &E7 Hardware Flow Control &E4Xon/Xoff Flow Control &E5 Hewlett-Packard ENQ/ACK Pacing &E9 Normal Mode Modem Flow Control On &E11Send Xon/Xoff Characters #X Terminal/Computer Initiated Pacing &E13Enq/Ack Pacing Commands Normal/Auto-Reliable/Reliable Mode CommandsXon/Xoff Pass-Through Commands Parity Selection #PModem Baud Rate $MB Speed Conversion CommandsSpeed Conversion $BA Serial Port Baud Rate $SB Immediate Action Commands Force Answer Mode a Off Hook HEnable/Disable Reading of Line Probe Information Commands Line Probe CommandsExiting Command Mode, Going Back On-Line O Format of Line Probe Graph or Table CommandsRegisters Escape Code Character Number of Rings Until Modem AnswersRings Which Have Occurred Return CharacterBackspace Character Time for Carrier Abort TimerLine Feed Character Wait Time for Dial ToneCarrier Detect Response Time S10 Carrier Loss Disconnect Delay TimeS13 Remote Configuration Escape Character S11 Tone Dialing Tone Spacing and DurationS17 Changing Break Time S15 Callback Time DelayS16 Callback Attempts S24 PBX/CBX Disconnect Drop Time for DSR/CTS/CDS30 Inactivity Timer S26 Failed Password AttemptsS29 Local Inactivity Timer S32 Time Elapse for Escape SequenceS37 Time Between DTR Active and Modem On-Hook Reading and Assigning S-Register ValuesS36 Time Between DTR Inactive and Modem Off-Hook S48 Program V.34bis Connect Speeds 2834 Series onlyExamples of Reading Values AT Command and S-Register SummaryExamples of Assigning Values Callback Security and Remote Configuration Callback Feature Description Remote Configuration DescriptionTo set parity of the password/message prompt To change your Remote Configuration feature statusTo turn your modems Callback Security feature on and off AT#DB2CR or AT#DB1CR Callback Operational Sequence Procedures Remote Configuration ProceduresCallback Security and Remote Configuration Remote Configuration Operation Procedures StepProcedureChange Login Password Remote Configuration and Callback Security AT CommandsCallback Security Enable/Disable AT#I=yyyyyyyyyyCRRemote Configuration/Callback Security S-Registers Local Inactivity Timer S29 DIP-Switch Settings DIP-Switch Option Settings PC BoardSwitch #4 AS/400 Mode Synchronous Mode/Leased Line/Dial-UP DIP-Switch SettingsMultiModemBA User Guide = Down Down Speaker Volume Control Switch #16 Reserved for Future UseRecording Option Configurations Switch Function Position EffectDIP Switches #13-14 DIP Switches #15-16Warranty, Service and Tech Support Multi-Tech Systems, Inc. Warranty & Repairs Policies Warranty, Service, and Technical SupportOnline Warranty Registration Repair Procedures for International DistributorsInternet Sites Replacement PartsTechnical Support Country TelephoneAppendixes Upgrade Overview Appendix a Upgrading Your Modem’s FirmwareDownload the Upgrade File Upgrade the Modem’s Firmware Modem Does Not Respond to Commands Appendix B TroubleshootingNone of the LEDs Light When the Modem Is On Appendix B Troubleshooting Modem Dials But Cannot Make a Connection File Transfer Is Slower Than It Should Be Modem Cannot Connect When AnsweringModem Disconnects While On-line Am Losing DataAm Getting Garbage Characters on the Monitor Command Values Description Apendix C AT Command SummaryAppendix C AT Command Summary MultiModemBA User Guide Command Values Description SN d$Fn RF n $SBn Break Atcr Callback Security/Remote Configuration Command Summary #Syyyyyyyyyy Password Command SummaryCommand Description #Ixxxxxxxxxx 25bis Commands 25bis Operation Delayed and Forbidden NumbersAppendix D V.25bis Operation 25bis Set-Up and Initialization 25bis Mode AT Commands25bis DIP-Switches Appendix D V.25bis OperationChange Serial Baud Rate CSP Command 25bis AT CommandsEnable/Disable V.25bis Mode $V Command 25bis Responses Result CodesListing Forbidden Phone Number RLF Command Dial Phone Number Provided CRN CommandListing Delayed Phone Numbers RLD Command Disregard or Connect to Incoming Calls DIC or CIC CommandItaly DTR Dialing $D CommandITU V.25bis Country Specific Information SwitzerlandBelgium Appendix E MultiModemBA Cables AustriaFrance SingaporeAppendix E MultiModemBA Cables Figure E-1. RS232 Cable IBM PCAppendix F Regulatory Information Appendix F Regulatory Information FCC PartFCC Part 68 Telecom Industry CanadaCanadian Limitations Notice 104105 EMC, Safety, and R&TTE Directive ComplianceInternational Modem Restrictions Index 106Index 107PBX/CBX Disconnect Drop Time for DSR/CTS/CD53 108109