Multi-Tech Systems MT5634MSV manual AT Commands, S-Registers & Result Codes, Remote Configuration

Page 6

MessageSaver User Guide

 

Stopping the Play of Voice Messages

26

Listening to the Next Voice Message

26

Listening to the Previous Voice Message

26

Erasing a Voice Message During Replay

26

Adjusting Speaker Volume

26

Using the MessageSaver in Speakerphone Mode

27

Remote Control

27

Controlling the MessageSaver Remotely

27

Activating Independent Mode Remotely

28

Chapter 4: AT Commands, S-Registers & Result Codes

 

AT Commands

30

AT Command Summary

31

S-Registers

42

Result Codes

45

Chapter 5: Remote Configuration

 

Introduction

48

Basic Procedure

48

Setup

48

Changing the Setup Password

48

Changing the Remote Escape Character

49

Chapter 6: Solving Problems

 

Introduction

52

None of the Indicators Light

52

The Modem Does Not Respond to Commands

53

The Modem Dials But Cannot Connect

54

The Modem Disconnects While Online

55

The Modem Cannot Connect When Answering

56

File Transfer Is Slower Than It Should Be

56

Data Is Being Lost

56

There Are Garbage Characters on the Monitor

57

The Modem Doesn’t Work with Caller ID

57

Fax and Data Software Can’t Run at the Same Time

57

Chapter 7: PhoneTools

 

Introduction

60

Installing PhoneTools

60

Using PhoneTools’ Status Bar

61

Phone Module

61

Making a Phone Call

61

Using the Speakerphone

62

Making Quick Dial Entries

62

Voice Module

63

Activating and Deactivating Answerphone

63

Setting up Answerphone

63

Setting Up the Answer Only Mode

64

Setting Up the Answer/Record Mode

64

vi

Image 6
Contents User Guide FCC Part User Guide Record of Revisions Introduction Quick StartMessageSaver Operation Solving Problems AT Commands, S-Registers & Result CodesRemote Configuration PhoneToolsAppendix a Regulatory Compliance Appendix C Loopback TestsAppendix D Warranty, Service, and Technical Support Appendix E Upgrade ProceduresIntroduction Introduction Product Description What Is in Your Modem Package? How to Get a Copy of Your User Guide Related ManualsMessageSaver User Guide Quick Start What You Will Need Safety WarningsIntroduction We supplyMount the Feet Select Stereo or Mono SpeakerOpening the Modem Changing the Speaker Jumper Location of speaker jumperConnect the Modem to Your System RS232 ConnectionLine Connection Phone Connection Power ConnectionPower-On Test Microphone ConnectionInstall the Modem in Windows Adding the Modem to WindowsRemoving Your Old Modem from Windows Install and Configure Your Software Call the Multi-Tech BBS Windows HyperTerminal Windows Terminal Send a Fax Microsoft FaxSelect Start Programs Accessories Fax Compose new fax ReferencesMessageSaver User Guide MessageSaver Operation PhoneTools Features Independent Mode FunctionsRecording and Downloading an Announcement MessageSaver OperationIndependent Mode Operation in PhoneTools Independent Mode Configuration Dialog BoxIndependent Mode Control Dialog Box Independent Mode Control dialog boxIndependent Mode Operation Using the Front Panel Control ButtonsIndicator Lights Playing Voice Messages Adjusting Speaker VolumeAnswering a Call with the Speakerphone Stopping the Play of Voice MessagesRemote Control Using the MessageSaver in Speakerphone ModeControlling the MessageSaver Remotely Activating Independent Mode Remotely Remote Control KeysAT Commands Registers Result Codes AT Commands AT Command Summary Echo Online Data Characters Echo Command Mode CharactersDS=y Dial Stored Telephone Number Hook ControlReturn Online to Data Mode Monitor Speaker VolumeMonitor Speaker Mode Modulation HandshakeSr? Read Register Value Result Codes Enable/DisableSet Register Value Tone DialingAuto Retrain Modem ResetLong Space Disconnect Data Carrier Detect DCD ControlAsynchronous Communications Mode Load Factory SettingsCommunications Mode 22bis Guard Tone ControlStore Current Configuration Test CommandsDisplay Current Settings Select Stored Configuration for Hard Reset\Gn Modem Port Flow Control \An\Bn Transmit Break \Jn Data Buffer Control\Nn Error Correction Mode Selection \Tn Inactivity Timer\Qn Flow Control Selection \Xn XON/XOFF Pass-Through DCn AT Command Control\Vn Protocol Result Code Data Calling Tone#S=x Store Setup Password Command +ES=n Enable Synchronous Buffered Mode#Sx Enter Setup Password Command +++ATCR Escape SequenceRegister Unit Range Default Description RegistersRegister Unit Range Default Description S37 Register Unit Range Default Description S42 Result Codes Terse Verbose DescriptionBlacklist Full Remote Configuration Basic Procedure SetupChanging the Setup Password Changing the Remote Escape Character MessageSaver User Guide Solving Problems None of the Indicators Light Modem Does Not Respond to Commands Modem Dials But Cannot Connect Modem4Disconnects While Online Modem4Cannot Connect When Answering File Transfer4Is Slower Than It Should BeData Is Being Lost There Are Garbage4 Characters on the Monitor Modem4Doesn’t Work with Caller IDFax and Data4Software Can’t Run at the Same Time MessageSaver User Guide PhoneTools Installing PhoneTools Using PhoneTools’ Status Bar Phone ModuleMaking a Phone Call Using the Speakerphone Making Quick Dial EntriesSetting up Answerphone Voice ModuleActivating and Deactivating Answerphone Setting Up the Answer Only Mode Setting Up the Answer/Record ModeListening to Received Messages from a Remote Phone Listening to Received Messages in PhoneToolsRecording an Announcement Changing Recording ParametersIndependent Mode Configuring and Controlling Independent Mode OperationHow Does It Work? Activating and Configuring Independent Mode Selecting an AnnouncementIndependent Mode Managing Stored Documents InboxFax Module Faxing a Document from a Windows ApplicationFaxing a File Directly from PhoneTools Sending a CoverAdding a Logo to the Cover Viewing and Printing FaxesInbox and Outbox Management Inbox ManagementOutbox Management Importing Existing Records Phone BookCreating New Records Selecting RecordsUsing the Phone Book for Dialing Terminal Emulation Module Starting a Modem ConnectionUploading Files to a Remote System Capturing Information to DiskData File Transfer Sending a Data File AutomaticallyReceiving a Data File Automatically Appendixes Appendix a Regulatory Compliance FCC Part 68 TelecomFax Branding Statement Regulatory ComplianceCanadian Limitations Notice International Modem RestrictionsCommission Decision CTR21 EMC and Safety Compliance New Zealand Telecom Warning NoticeMessageSaver User Guide Appendix B Technical Specifications Carrier Frequencies Frequency Stability MessageSaver User Guide Test procedure Local Analog Loopback Test V.54 LoopRemote Digital Loopback Test V.54 Loop Figure C-2. Remote digital loopback testLocal Digital Loopback Test V.54 Loop Figure C-3. Local digital loopback testMessageSaver User Guide Limited Warranty ServiceOnline Warranty Registration Technical SupportMulti-Tech BBS About the Internet Modem Accessories About the Multi-Tech Fax-Back ServiceSupplyNet Online Ordering Instructions Upgrade Overview Identify the Modem FirmwareIdentify the Current Firmware Version Multi-Tech Web SiteMulti-Tech BBS Download the Upgrade File Extract the Upgrade FilesClear Your Stored Paramenters Upgrade the Modem’s Firmware Restore Your ParametersIndex Symbols Index 106