Multi-Tech Systems MT5634MSV DS=y Dial Stored Telephone Number, Echo Command Mode Characters

Page 40

MessageSaver User Guide

		V	Switch to speakerphone mode and dial the following num-
			ber. Use ATH command to hang up.
		W	Wait for a new dial tone before continuing to dial. (X2, X4,
			X5, X6, or X7 must be selected.)
		,	Pause during dialing for time set in register S8.
		;	Return to command mode after dialing. (Place at end of
			dial string.)
		!	Hook flash. Causes the modem to go on-hook for one-half
			second, then off-hook again.
		@	Wait for quiet answer. Causes modem to wait for a ring-
			back, then 5 seconds of silence, before processing next part
			of command. If silence is not detected, the modem returns
			a NO ANSWER code.
		^	Disable data calling tone transmission.
		$	Detect AT&T call card “bong” tone. The character should
			follow the phone number and precede the user’s call card
			number: ATDT1028806127853500$123456789
Command:	DS=y Dial Stored Telephone Number
Values:		y = 0–3
Default:		none
Description:		Dial a number previously stored in directory number y by the
		&Zy=x command. Example: ATDS=3.
Command:	En	Echo Command Mode Characters
Values:		n = 0 or 1
Default:		1
Description:	E0	Do not echo keyboard input to the terminal.
	E1	Do echo keyboard input to the terminal.
Command:	Fn	Echo Online Data Characters
Values:		n = 1
Default:		1
Description:	F0	Enable online data character echo. (Not supported.)
	F1	Disable online data character echo (included for backward
		compatibility with some software).
Command:	Hn	Hook Control
Values:		n = 0 or 1
Default:		0
Description: H0 Go on-hook (hang up).
	H1	Go off-hook (make the phone line busy).
Command:	In	Information Request
Values:		n = 0–5, 9, 11
Default:		None
Description:	I0	Display default speed and controller firmware version.
	I1	Calculate and display ROM checksum (e.g., 12AB).
	I2	Check ROM and verify the checksum, displaying OK or ERROR.
	I3	Display default speed and controller firmware version.
	I4	Display firmware version for data pump (e.g., 94).

32

Image 40

Contents User Guide FCC Part User Guide Record of Revisions Quick Start IntroductionMessageSaver Operation AT Commands, S-Registers & Result Codes Remote ConfigurationSolving Problems PhoneToolsAppendix a Regulatory Compliance Appendix C Loopback TestsAppendix D Warranty, Service, and Technical Support Appendix E Upgrade ProceduresIntroduction Introduction Product Description What Is in Your Modem Package? How to Get a Copy of Your User Guide Related ManualsMessageSaver User Guide Quick Start Safety Warnings IntroductionWhat You Will Need We supplySelect Stereo or Mono Speaker Mount the FeetOpening the Modem Changing the Speaker Jumper Location of speaker jumperRS232 Connection Connect the Modem to Your SystemLine Connection Power Connection Power-On TestPhone Connection Microphone ConnectionAdding the Modem to Windows Install the Modem in WindowsRemoving Your Old Modem from Windows Install and Configure Your Software Call the Multi-Tech BBS Windows HyperTerminal Windows Terminal Send a Fax Microsoft FaxSelect Start Programs Accessories Fax Compose new fax ReferencesMessageSaver User Guide MessageSaver Operation PhoneTools Features Independent Mode FunctionsRecording and Downloading an Announcement MessageSaver OperationIndependent Mode Operation in PhoneTools Independent Mode Configuration Dialog BoxIndependent Mode Control Dialog Box Independent Mode Control dialog boxIndependent Mode Operation Using the Front Panel Control ButtonsIndicator Lights Adjusting Speaker Volume Answering a Call with the SpeakerphonePlaying Voice Messages Stopping the Play of Voice MessagesUsing the MessageSaver in Speakerphone Mode Remote ControlControlling the MessageSaver Remotely Activating Independent Mode Remotely Remote Control KeysAT Commands Registers Result Codes AT Commands AT Command Summary Echo Command Mode Characters DS=y Dial Stored Telephone NumberEcho Online Data Characters Hook ControlMonitor Speaker Volume Monitor Speaker ModeReturn Online to Data Mode Modulation HandshakeResult Codes Enable/Disable Set Register ValueSr? Read Register Value Tone DialingModem Reset Long Space DisconnectAuto Retrain Data Carrier Detect DCD ControlLoad Factory Settings Communications ModeAsynchronous Communications Mode 22bis Guard Tone ControlTest Commands Display Current SettingsStore Current Configuration Select Stored Configuration for Hard Reset\An \Bn Transmit Break\Gn Modem Port Flow Control \Jn Data Buffer Control\Tn Inactivity Timer \Nn Error Correction Mode Selection\Qn Flow Control Selection DCn AT Command Control \Vn Protocol Result Code\Xn XON/XOFF Pass-Through Data Calling ToneCommand +ES=n Enable Synchronous Buffered Mode #Sx Enter Setup Password#S=x Store Setup Password Command +++ATCR Escape SequenceRegister Unit Range Default Description RegistersRegister Unit Range Default Description S37 Register Unit Range Default Description S42 Result Codes Terse Verbose DescriptionBlacklist Full Remote Configuration Setup Basic ProcedureChanging the Setup Password Changing the Remote Escape Character MessageSaver User Guide Solving Problems None of the Indicators Light Modem Does Not Respond to Commands Modem Dials But Cannot Connect Modem4Disconnects While Online File Transfer4Is Slower Than It Should Be Modem4Cannot Connect When AnsweringData Is Being Lost Modem4Doesn’t Work with Caller ID There Are Garbage4 Characters on the MonitorFax and Data4Software Can’t Run at the Same Time MessageSaver User Guide PhoneTools Installing PhoneTools Phone Module Using PhoneTools’ Status BarMaking a Phone Call Using the Speakerphone Making Quick Dial EntriesVoice Module Setting up AnswerphoneActivating and Deactivating Answerphone Setting Up the Answer Only Mode Setting Up the Answer/Record ModeListening to Received Messages from a Remote Phone Listening to Received Messages in PhoneToolsRecording an Announcement Changing Recording ParametersConfiguring and Controlling Independent Mode Operation Independent ModeHow Does It Work? Activating and Configuring Independent Mode Selecting an AnnouncementIndependent Mode Managing Stored Documents InboxFax Module Faxing a Document from a Windows ApplicationFaxing a File Directly from PhoneTools Sending a CoverAdding a Logo to the Cover Viewing and Printing FaxesInbox and Outbox Management Inbox ManagementOutbox Management Phone Book Creating New RecordsImporting Existing Records Selecting RecordsUsing the Phone Book for Dialing Terminal Emulation Module Starting a Modem ConnectionUploading Files to a Remote System Capturing Information to DiskData File Transfer Sending a Data File AutomaticallyReceiving a Data File Automatically Appendixes Appendix a Regulatory Compliance FCC Part 68 TelecomFax Branding Statement Regulatory ComplianceInternational Modem Restrictions Canadian Limitations NoticeCommission Decision CTR21 EMC and Safety Compliance New Zealand Telecom Warning NoticeMessageSaver User Guide Appendix B Technical Specifications Carrier Frequencies Frequency Stability MessageSaver User Guide Test procedure Local Analog Loopback Test V.54 LoopRemote Digital Loopback Test V.54 Loop Figure C-2. Remote digital loopback testLocal Digital Loopback Test V.54 Loop Figure C-3. Local digital loopback testMessageSaver User Guide Limited Warranty ServiceTechnical Support Online Warranty RegistrationMulti-Tech BBS About the Internet About the Multi-Tech Fax-Back Service Modem AccessoriesSupplyNet Online Ordering Instructions Upgrade Overview Identify the Modem FirmwareMulti-Tech Web Site Identify the Current Firmware VersionMulti-Tech BBS Extract the Upgrade Files Download the Upgrade FileClear Your Stored Paramenters Upgrade the Modem’s Firmware Restore Your ParametersIndex Symbols Index 106