CYD01S36V
CYD02S36V/36VA/CYD04S36V
CYD09S36V/CYD18S36V
Master Reset
The FLEx36 family devices undergo a complete reset by taking its MRST input LOW. The MRST input can switch asynchro- nously to the clocks. An MRST initializes the internal burst counters to zero, and the counter mask registers to all ones (completely unmasked). MRST also forces the Mailbox Interrupt (INT) flags and the Counter Interrupt (CNTINT) flags HIGH. MRST must be performed on the FLEx36 family devices after power up.
Mailbox Interrupts
The upper two memory locations may be used for message passing and permit communications between ports. Table 2 shows the interrupt operation for both ports of CYD18S36V. The highest memory location, 7FFFF is the mailbox for the right port and 7FFFE is the mailbox for the left port. Table 2 shows that to set the INTR flag, a Write operation by the left port to address 7FFFF asserts INTR LOW. At least one byte must be active for a Write to generate an interrupt. A valid Read of the 7FFFF location by the right port resets INTR HIGH. At least one byte must be active in order for a Read to reset the interrupt. When one port Writes to the other port’s mailbox, the INT of the port that the mailbox belongs to is asserted LOW. The INT is reset when the owner (port) of the mailbox Reads the contents of the mailbox. The interrupt flag is set in a
Each port can read the other port’s mailbox without resetting the interrupt. And each port can write to its own mailbox without setting the interrupt. If an application does not require message passing, INT pins must be left open.
Table 2. Interrupt Operation Example [1, 14, 15, 16, 17, 18]
Address Counter and Mask Register Operations[19]
This section describes the features only apply to 1Mbit, 2 Mbit, 4 Mbit and 9 Mbit devices. It does not apply to 18Mbit device. Each port of these devices has a programmable burst address counter. The burst counter contains three registers: a counter register, a mask register, and a mirror register.
The counter register contains the address used to access the RAM array. It is changed only by the Counter Load, Increment, Counter Reset, and by master reset (MRST) operations.
The mask register value affects the Increment and Counter Reset operations by preventing the corresponding bits of the counter register from changing. It also affects the counter interrupt output (CNTINT). The mask register is changed only by the Mask Load and Mask Reset operations, and by the MRST. The mask register defines the counting range of the counter register. It divides the counter register into two regions: zero or more “0s” in the most significant bits define the masked region, one or more “1s” in the least significant bits define the unmasked region. Bit 0 may also be “0,” masking the least significant counter bit and causing the counter to increment by two instead of one.l
The mirror register is used to reload the counter register on increment operations (see “retransmit,” below). It always contains the value last loaded into the counter register, and is changed only by the Counter Load, and Counter Reset opera- tions, and by the MRST.
Table 3 on page 6 summarizes the operation of these registers and the required input control signals. The MRST control signal is asynchronous. All the other control signals in Table 3 on page 6 (CNT/MSK, CNTRST, ADS, CNTEN) are synchronized to the port’s CLK. All these counter and mask operations are independent of the port’s chip enable inputs (CE0 and CE1).
| Function |
|
|
|
|
|
| Left Port |
|
|
|
|
|
|
|
| Right Port |
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
R/WL |
| CEL |
| INTL | R/WR |
| CER |
| INTR | |||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||||
Set Right |
|
|
|
| R Flag | L |
| L | 7FFFF |
| X | X |
| X | X |
| L | |||||||||||
INT | ||||||||||||||||||||||||||||
Reset Right |
|
|
| R Flag | X |
| X | X |
| X | H |
| L | 7FFFF |
| H | ||||||||||||
INT | ||||||||||||||||||||||||||||
Set Left |
|
|
| L Flag | X |
| X | X |
| L | L |
| L | 7FFFE |
| X | ||||||||||||
INT | ||||||||||||||||||||||||||||
Reset Left |
|
|
|
| L Flag | H |
| L | 7FFFE |
| H | X |
| X | X |
| X | |||||||||||
INT | ||||||||||||||||||||||||||||
Notes
13.This family of
14.CE is internal signal. CE = LOW if CE0 = LOW and CE1 = HIGH. For a single Read operation, CE only needs to be asserted once at the rising edge of the CLK and can be deasserted after that. Data is out after the following CLK edge and is
15.OE is “Don’t Care” for mailbox operation.
16.At least one of BE0, BE1, BE2, or BE3 must be LOW.
17.A17x is a NC for CYD04S36V, therefore the Interrupt Addresses are 1FFFF and 1FFFE. A17x and A16x are NC for CYD02S36V/36VA, therefore the Interrupt Addresses are FFFF and FFFE; A17x, A16x and A15x are NC for CYD01S36V, therefore the Interrupt Addresses are 7FFF and 7FFE.
18.“X” = “Don’t Care,” “H” = HIGH, “L” = LOW.
19.This section describes the CYD09S36V, CYD04S36V, CYD02S36V/36VA, and CYD01S36V which have 18, 17, 16 and 15 address bits.
Document Number: | Page 5 of 28 |
[+] Feedback