Datacom Systems VS-1200 manual Rear Panel Description, Management Port

Page 15

Hardware

15

LX-BT/SX-BT - The LEDs located to the right of the SFP connectors are solid green indicating a link has been detected between the respective Any-to-Any Rx port and network device/tool Tx port or network segment. The LEDs are flashing green when data is passed.

LX-SFP/SX-SFP/VS-SFP - The LED located below and slightly left of center of the SFP connectors are solid green indicating a link has been detected between the respective Any-to-Any Rx port and network device/tool Tx port or network segment. The LED flashes green when data is passed. The LED located below and slightly right of center of the SFP connectors indicates the line speed of each port. See the Any-to-Any SFP LED Display Code table for LED display codes.

3.2.3Management Port

The MANAGEMENT PORT is an RJ45 socket used for 100 Mbs full-duplex connection with a straight-through LAN cable via your management LAN to a Remote Management Console which is a standard PC using any Telnet terminal emulation application.

Link indicates connection. The LED Display Code table deciphers the RJ45 jacks with integrated LEDs that display line status of the MANAGEMENT PORT.

3.3Rear Panel Description

This section provides a description of the rear panel of the VS-1200 series.

or

An explanation of each rear panel legend follows:

© 2009 Datacom Systems Inc

Image 15

Contents USERguide Page Product Description Datacom Systems Inc VS-1200 Data Acccess SwitchTable of Contents Hardware Installation Customer ServiceVS-1200 Series Functional Drawing Application Certifications and Marks Terms of UseCopyright License Agreement Trademark Attribution Proprietary NoticeSafety Notices and Warnings VS-1200 Series Summary OverviewWhat Shipped? VS-1200 Series Features and BenefitsOperating Range Relative Humidity 5 to 90% non-condensing VS-1200 Series Common SpecificationsVS-1200 Series Model Specific Specifications Power Consumption 12W BTU/hPage Hardware VS-1200 Series Front PanelsVS-1210BT/SFP Power Front Panel DescriptionAny-to-Any Ports Management Port Rear Panel DescriptionRear Label BT series Power Switch SFP seriesInput Power Serial DB9Initial Configuration Command Line Interface CLIBasic Functionality Basic Commands Read Only Access Password RecoverySET Port Monitor SE PO MO TAP Show Groups SH GR Group NameShow Port Routing SH PO RO Superuser Commands Configuration Access SU SET Password SU SE PAShow Users SH US SET Date Mmddyy # SET IP Subnet Gateway# SE PO MO 3 OFF SET Time HhmmssADD User AD US Serial Port Configuration DB9 Delete User UsernameHyperTerminal Management Port Configuration RJ45 TCP/IP WinsockPort Number IP Address Configuration IP Address Configuration with HyperTerminalTelnet Accessories Communications HyperTerminal VS-1200 Data Acccess Switch Initial Configuration IP Address Configuration with Telnet Network Connections Accessories Command Prompt Initial Configuration Exercise CLI Setting Ports Initial Configuration # SET Port Monitor 2 from 8,9 # SET Port Monitor 1 from 7,9# SET Port Monitor 8 from # SET Port Monitor 5 from# SET Port Monitor 6 from 3,4 # SET Port Monitor 7 fromSafety Guidelines Small Form-Factor Plug ModuleIntallation Prerequisites Removing the SFP Module Installing the SFP ModulePage Hardware Installation PowerAny-to-Any Connection Management Connection VS-1210BT-BT/SFP VS-1200 Series Functional DrawingVS-1204BT VS-1204SFP Application Gathering the Data HyperTerminal configuration exampleVS-1200 Data Acccess Switch # SET Port Monitor 4 from # SET Port Monitor 6 from# SET Port Monitor 9 from VS-1200 Data Acccess Switch Application # SET Port Monitor 8 from 2,4 # SET Port Monitor 5 from 1,3# SET Port Monitor 6 from 1,3 # SET Port Monitor 7 from 2,4Customer Service Internet WarrantyLimits of Liability Datacom Systems Inc