Datacom Systems VS-1200 manual Management Port Configuration RJ45, TCP/IP Winsock, Port Number

Page 27

Initial Configuration

4.3 MANAGEMENT Port Configuration (RJ45)

27

Once VS-1200 series connection is made to the MANAGEMENT RJ45 port, open the terminal emulation application and create a connection with settings that fit your needs:

The factory configured VS-1200 series IP Address, Subnet Mask and Default Gateway are as follows:

IP Address: 192.168.1.1; Subnet Mask: 255.255.255.0; Default Gateway: 0.0.0.0

4.3.1HyperTerminal

The following example utilizes Microsoft HyperTerminal. Any freely available terminal emulator may be utilized, but please take note of the specific HyperTerminal setup settings if an alternate terminal emulator is used.

IMPORTANT: For Host Address, if initial IP Address HAS NOT BEEN configured, use 192.168.1.1

(default) or if initial IP Address HAS BEEN configured, use the Local Area Network address input during initial IP Address configuration.

HyperTerminal (terminal emulator) enter:

TCP/IP (Winsock)

Host Address: nnn.nnn.nnn.nnn [i.e., 192.168.1.1 or Local Area Network]

Port Number: 23

Set HyperTerminal (terminal emulator) properties

Under File>Properties>Settings

Emulation: VT100

Under File>Properties>Settings>ASCII Setup

Check box: Send line ends with line feeds

Check box: Echo typed characters locally

After completing review of the Command Line Interface (CLI) 17 section and Exercise - CLI setting Ports 36 section, detailed IP Address configuration can be found in the IP Address Configuration 28 section.

© 2009 Datacom Systems Inc

Image 27

Contents USERguide Page Product Description Datacom Systems Inc VS-1200 Data Acccess SwitchTable of Contents Hardware Installation Customer ServiceVS-1200 Series Functional Drawing Application Certifications and Marks Terms of UseCopyright License Agreement Trademark Attribution Proprietary NoticeSafety Notices and Warnings VS-1200 Series Summary OverviewWhat Shipped? VS-1200 Series Features and BenefitsOperating Range Relative Humidity 5 to 90% non-condensing VS-1200 Series Common SpecificationsVS-1200 Series Model Specific Specifications Power Consumption 12W BTU/hPage Hardware VS-1200 Series Front PanelsVS-1210BT/SFP Power Front Panel DescriptionAny-to-Any Ports Management Port Rear Panel DescriptionRear Label BT series Power Switch SFP seriesInput Power Serial DB9Initial Configuration Command Line Interface CLIBasic Functionality Basic Commands Read Only Access Password RecoverySET Port Monitor SE PO MO TAP Show Groups SH GR Group NameShow Port Routing SH PO RO Superuser Commands Configuration Access SU SET Password SU SE PAShow Users SH US SET Date Mmddyy # SET IP Subnet Gateway# SE PO MO 3 OFF SET Time HhmmssADD User AD US Serial Port Configuration DB9 Delete User UsernameHyperTerminal Management Port Configuration RJ45 TCP/IP WinsockPort Number IP Address Configuration IP Address Configuration with HyperTerminalTelnet Accessories Communications HyperTerminal VS-1200 Data Acccess Switch Initial Configuration IP Address Configuration with Telnet Network Connections Accessories Command Prompt Initial Configuration Exercise CLI Setting Ports Initial Configuration # SET Port Monitor 2 from 8,9 # SET Port Monitor 1 from 7,9# SET Port Monitor 8 from # SET Port Monitor 5 from# SET Port Monitor 6 from 3,4 # SET Port Monitor 7 fromSafety Guidelines Small Form-Factor Plug ModuleIntallation Prerequisites Removing the SFP Module Installing the SFP ModulePage Hardware Installation PowerAny-to-Any Connection Management Connection VS-1210BT-BT/SFP VS-1200 Series Functional DrawingVS-1204BT VS-1204SFP Application Gathering the Data HyperTerminal configuration exampleVS-1200 Data Acccess Switch # SET Port Monitor 4 from # SET Port Monitor 6 from# SET Port Monitor 9 from VS-1200 Data Acccess Switch Application # SET Port Monitor 8 from 2,4 # SET Port Monitor 5 from 1,3# SET Port Monitor 6 from 1,3 # SET Port Monitor 7 from 2,4Customer Service Internet WarrantyLimits of Liability Datacom Systems Inc