Datacom Systems VS-1200 manual Installing the SFP Module, Removing the SFP Module

Page 41

Initial Configuration

41

4.6.3Installing the SFP Module

SFP modules might ship already installed in your VS-1200, or they might arrive packaged separately. This section describes how to install the SFP module.

NOTE: You can install SFP modules with power on to the system; however, it is strongly recommended that you do not install the SFP module with fiber or copper cables attached to it. Disconnect all cables before installing a SFP module.

CAUTION: Prevent system problems, use only Datacom Systems Inc. supplied SFP modules.

Step 1. Turn the SFP module so the latch is towards the center of the Gigabit Ethernet Interface sockets. The SFP module is keyed so that it cannot be inserted incorrectly.

Step 2. Insert the SFP module into the SFF port and repeat Step 1 and Step 2 inserting other SFP modules until completed.

Step 3. Attach the appropriate network cable to the LC-type or RJ45-type connector on the SFP module. For fiber optic SFP modules you can use either simplex or duplex connectors. For simplex connectors, two cables are required, one cable for transmit (Rx) and a second cable for receive (Rx). For duplex connectors, only one cable that has both Tx and Rx connectors is required.

4.6.4Removing the SFP Module

SFP modules might ship already installed in your VS-1200, or they might arrive packaged separately. This section describes how to remove the SFP module.

NOTE: You can remove SFP modules with power on to the system; however, it is strongly recommended that you do not remove the SFP module with fiber or copper cables attached to it. Disconnect all cables before removing a SFP module.

Step 1. Disconnect the network cable from the SFP module LC-type or RJ45-type connector.

Step 2. Release the SFP module from the GE SFF port by moving the swing latch away from the body of the unit.

Step 3. Slide the SFP module out of the GE SFF port.

© 2009 Datacom Systems Inc

Image 41

Contents USERguide Page Product Description Datacom Systems Inc VS-1200 Data Acccess SwitchTable of Contents VS-1200 Series Functional Drawing Application Hardware InstallationCustomer Service Copyright License Agreement Trademark Attribution Terms of UseProprietary Notice Certifications and MarksSafety Notices and Warnings VS-1200 Series Summary OverviewWhat Shipped? VS-1200 Series Features and BenefitsVS-1200 Series Model Specific Specifications VS-1200 Series Common SpecificationsPower Consumption 12W BTU/h Operating Range Relative Humidity 5 to 90% non-condensingPage VS-1210BT/SFP HardwareVS-1200 Series Front Panels Any-to-Any Ports PowerFront Panel Description Management Port Rear Panel DescriptionInput Power Power Switch SFP seriesSerial DB9 Rear Label BT seriesBasic Functionality Initial ConfigurationCommand Line Interface CLI Basic Commands Read Only Access Password RecoverySET Port Monitor SE PO MO TAP Show Groups SH GR Group NameShow Port Routing SH PO RO Show Users SH US Superuser Commands Configuration AccessSU SET Password SU SE PA SET Date Mmddyy # SET IP Subnet Gateway# SE PO MO 3 OFF SET Time HhmmssADD User AD US HyperTerminal Serial Port Configuration DB9Delete User Username Port Number Management Port Configuration RJ45TCP/IP Winsock Telnet IP Address ConfigurationIP Address Configuration with HyperTerminal Accessories Communications HyperTerminal VS-1200 Data Acccess Switch Initial Configuration IP Address Configuration with Telnet Network Connections Accessories Command Prompt Initial Configuration Exercise CLI Setting Ports Initial Configuration # SET Port Monitor 2 from 8,9 # SET Port Monitor 1 from 7,9# SET Port Monitor 6 from 3,4 # SET Port Monitor 5 from# SET Port Monitor 7 from # SET Port Monitor 8 fromIntallation Prerequisites Safety GuidelinesSmall Form-Factor Plug Module Removing the SFP Module Installing the SFP ModulePage Any-to-Any Connection Hardware InstallationPower Management Connection VS-1210BT-BT/SFP VS-1200 Series Functional DrawingVS-1204BT VS-1204SFP Application Gathering the Data HyperTerminal configuration exampleVS-1200 Data Acccess Switch # SET Port Monitor 9 from # SET Port Monitor 4 from# SET Port Monitor 6 from VS-1200 Data Acccess Switch Application # SET Port Monitor 6 from 1,3 # SET Port Monitor 5 from 1,3# SET Port Monitor 7 from 2,4 # SET Port Monitor 8 from 2,4Limits of Liability Customer ServiceInternet Warranty Datacom Systems Inc