Datacom Systems VS-1200 manual Small Form-Factor Plug Module, Intallation Prerequisites

Page 40

40

VS-1200 Data Acccess Switch

4.6Small Form-Factor Plug Module

This section provides information about small form-factor plug (SFP) modules. The SFP modules are input/output devices that plug into a Gigabit Ethernet (GE) small form-factor (SFF) port, linking the port with a 1000Base-X fiber or 1000Base-T copper network.

The fiber SFP module have a receiver port (Rx) and a transmitter port (Tx) that make up one optical interface.The 1000Base-SX (short wavelength) SFP module operates on standard multimode fiber networks compliant with the 1000Base SX standard. The 1000Base-LX (long wavelength) SFP module operates on standard single-mode fiber networks compliant with the 1000Base LX standard. The fiber SFP module is a 1000 Mbps optical interface in the form of an LC-type duplex port that supports interfaces compliant with the 1000Base-X standard.

The copper SFP module is compliant with the 1000Base-T standard and operates on standard Category 5 wiring and has an RJ45 connector.

4.6.1Intallation Prerequisites

This section describes safety and compliance guidelines you should observe before you install an SFP module in your VS-1200 series unit.

NOTE: You can install and remove SFP modules with power on to the system; however, it is strongly recommended that you do not install or remove the SFP module with fiber or copper cables attached to it. Disconnect all cables before removing or installing a SFP module.

CAUTION: Prevent system problems, use only Datacom Systems Inc. supplied SFP modules.

4.6.2Safety Guidelines

Before handling a SFP module, observe the following guidelines:

∙Copper and fiber SFP modules are static-sensitive. To prevent electrostatic discharge (ESD) damage, follow your normal ESD handling procedures.

∙Fiber SFP modules are dust-sensitive. When storing a SFP module or when a fiber cable is not plugged in, always keep plugs in the SFP module optical hole.

∙The most common source of contaminants in the fiber SFP optical aperture is debris picked up on the terminations of the optical connectors. Use an alcohol swab or lint-free absorbent wipes to clean the terminations of the optical connector.

WARNING: Fiber SFP modules are class 1 laser and LED products. Invisible laser radiation may be emitted from the port opening when no fiber cable is connected, avoid exposure to laser radiation and do not stare in open optical ports.

© 2009 Datacom Systems Inc

Page 39 Page 41
Image 40
Page 39 Page 41
Contents USERguide Page Product Description VS-1200 Data Acccess Switch Datacom Systems IncTable of Contents Customer Service Hardware InstallationVS-1200 Series Functional Drawing Application Terms of Use Copyright License Agreement Trademark AttributionProprietary Notice Certifications and MarksSafety Notices and Warnings Overview VS-1200 Series SummaryVS-1200 Series Features and Benefits What Shipped?VS-1200 Series Common Specifications VS-1200 Series Model Specific SpecificationsPower Consumption 12W BTU/h Operating Range Relative Humidity 5 to 90% non-condensingPage VS-1200 Series Front Panels HardwareVS-1210BT/SFP Front Panel Description PowerAny-to-Any Ports Rear Panel Description Management PortPower Switch SFP series Input PowerSerial DB9 Rear Label BT seriesCommand Line Interface CLI Initial ConfigurationBasic Functionality Password Recovery Basic Commands Read Only AccessSET Port Monitor SE PO MO Show Groups SH GR Group Name TAPShow Port Routing SH PO RO SU SET Password SU SE PA Superuser Commands Configuration AccessShow Users SH US # SET IP Subnet Gateway SET Date MmddyySET Time Hhmmss # SE PO MO 3 OFFADD User AD US Delete User Username Serial Port Configuration DB9HyperTerminal TCP/IP Winsock Management Port Configuration RJ45Port Number IP Address Configuration with HyperTerminal IP Address ConfigurationTelnet Accessories Communications HyperTerminal VS-1200 Data Acccess Switch Initial Configuration IP Address Configuration with Telnet Network Connections Accessories Command Prompt Initial Configuration Exercise CLI Setting Ports Initial Configuration # SET Port Monitor 1 from 7,9 # SET Port Monitor 2 from 8,9# SET Port Monitor 5 from # SET Port Monitor 6 from 3,4# SET Port Monitor 7 from # SET Port Monitor 8 fromSmall Form-Factor Plug Module Safety GuidelinesIntallation Prerequisites Installing the SFP Module Removing the SFP ModulePage Power Hardware InstallationAny-to-Any Connection Management Connection VS-1200 Series Functional Drawing VS-1210BT-BT/SFPVS-1204BT VS-1204SFP Gathering the Data HyperTerminal configuration example ApplicationVS-1200 Data Acccess Switch # SET Port Monitor 6 from # SET Port Monitor 4 from# SET Port Monitor 9 from VS-1200 Data Acccess Switch Application # SET Port Monitor 5 from 1,3 # SET Port Monitor 6 from 1,3# SET Port Monitor 7 from 2,4 # SET Port Monitor 8 from 2,4Internet Warranty Customer ServiceLimits of Liability Datacom Systems Inc
Top Page Image Contents