Datacom Systems VS-1200 manual Hardware Installation, Power, Any-to-Any Connection

Page 43

Hardware Installation

5 Hardware Installation

43

This section describes the VS-1200 series hardware installation at the network site of your choice.

For specific VS-1200 applications see the 'Application

47' section.

5.1Power

This section describes the power connection at the network installation site of the VS-1200 configurable series.

or

Two DC input power sockets are provided on the rear panel. The front panel POWER 1 and 2 LEDs are illuminated green, respectively:

∙(BT series) - when DC power is available at both the two rear DC power sockets; or

∙(SFP series) - when the DC POWER switch is depressed ON and DC power is available at both the two rear DC power sockets.

Either POWER 1 or 2 LED not illuminated when powered, indicates a defective power source and immediate investigation as to the cause is required to insure redundant power integrity.

1.Step 1. Using the supplied Power Adapters and AC Line Cords, plug the VS-1200 series into different circuit external power sources.Although only one power supply is required to power the configurable unit, use of a second independent power source is strongly recommended to assure uninterrupted monitoring. Furthermore, connecting the second Power Adapter to a different external power source circuit than the first AC power source eliminates power as a single point of failure.

5.2Any-to-Any Connection

This section will focus on the Any-to-Anyport connection of the typical VS-1200 series hardware

installation.

© 2009 Datacom Systems Inc

Image 43

Contents USERguide Page Product Description Datacom Systems Inc VS-1200 Data Acccess SwitchTable of Contents Customer Service Hardware InstallationVS-1200 Series Functional Drawing Application Certifications and Marks Terms of UseCopyright License Agreement Trademark Attribution Proprietary NoticeSafety Notices and Warnings VS-1200 Series Summary OverviewWhat Shipped? VS-1200 Series Features and BenefitsOperating Range Relative Humidity 5 to 90% non-condensing VS-1200 Series Common SpecificationsVS-1200 Series Model Specific Specifications Power Consumption 12W BTU/hPage VS-1200 Series Front Panels HardwareVS-1210BT/SFP Front Panel Description PowerAny-to-Any Ports Management Port Rear Panel DescriptionRear Label BT series Power Switch SFP seriesInput Power Serial DB9Command Line Interface CLI Initial ConfigurationBasic Functionality Basic Commands Read Only Access Password RecoverySET Port Monitor SE PO MO TAP Show Groups SH GR Group NameShow Port Routing SH PO RO SU SET Password SU SE PA Superuser Commands Configuration AccessShow Users SH US SET Date Mmddyy # SET IP Subnet Gateway# SE PO MO 3 OFF SET Time HhmmssADD User AD US Delete User Username Serial Port Configuration DB9HyperTerminal TCP/IP Winsock Management Port Configuration RJ45Port Number IP Address Configuration with HyperTerminal IP Address ConfigurationTelnet Accessories Communications HyperTerminal VS-1200 Data Acccess Switch Initial Configuration IP Address Configuration with Telnet Network Connections Accessories Command Prompt Initial Configuration Exercise CLI Setting Ports Initial Configuration # SET Port Monitor 2 from 8,9 # SET Port Monitor 1 from 7,9# SET Port Monitor 8 from # SET Port Monitor 5 from# SET Port Monitor 6 from 3,4 # SET Port Monitor 7 fromSmall Form-Factor Plug Module Safety GuidelinesIntallation Prerequisites Removing the SFP Module Installing the SFP ModulePage Power Hardware InstallationAny-to-Any Connection Management Connection VS-1210BT-BT/SFP VS-1200 Series Functional DrawingVS-1204BT VS-1204SFP Application Gathering the Data HyperTerminal configuration exampleVS-1200 Data Acccess Switch # SET Port Monitor 6 from # SET Port Monitor 4 from# SET Port Monitor 9 from VS-1200 Data Acccess Switch Application # SET Port Monitor 8 from 2,4 # SET Port Monitor 5 from 1,3# SET Port Monitor 6 from 1,3 # SET Port Monitor 7 from 2,4Internet Warranty Customer ServiceLimits of Liability Datacom Systems Inc