Datacom Systems VS-1200 Initial Configuration, Command Line Interface CLI, Basic Functionality

Page 17

Initial Configuration

17

4 Initial Configuration

IMPORTANT: Prior to initial configuration of the hardware, it is imperative to review the

entire Initial Configuration section before proceeding to the Installation section.

This section explains the considerations and requirements for the initial configuration of the VS-1200 series by a Command Line Interface (CLI) with a management PC using a terminal emulation application connected either through the SERIAL DB9 port or though the MANAGEMENT RJ45 port. Only one configuration session can be open at a time.

4.1Command Line Interface (CLI)

The Command Line Interface (CLI ) is used to:

∙set IP address (default 192.168.1.1), Subnet Mask (default 255.255.255.0) and Gateway (default 0.0.0.0)

∙set port speed and duplex

∙enables the user to select which ports or groups of ports receive the data stream copies

∙allows Any-to-Any ports to be configured as either inputs or outputs.

The VS-1200 series factory default is off for all Any-to-Any ports.

4.1.1Basic Functionality

Window Size Functionality: The CLI window is limited to 24 lines per screen and 80 characters per line. If more data than can fit is presented, a “-more-” prompt is shown on the last line.

Character Handling: Printable character (ASCII code 32-126) and non-printable noted below:

Non-Printable Character

Description

∙ <enter key>

Executes command; places command in history buffer

∙ <backspace key>

Erases previous character entry; removes history buffer entry

Connectivity/Authentication Functionality: Connectivity to the configurable product is made through the Management RJ45 or Serial DB9 port and authentication is required. This password protection yields read-only access. To make configuration changes, Superuser (SU) mode must be accessed with another password. See the 'Superuser Commands 22 ' section for more information.

Base Prompt: This is the text presented to the user logging in to use the CLI (default values shown). All Usernames and passwords are case-sensitive.

Enter Username: Administrator

Enter Password: admin

>

Superuser log in:

Example: > SU

Enter Password: password

#

© 2009 Datacom Systems Inc

Page 16 Page 18
Image 17
Page 16 Page 18
Contents USERguide Page Product Description Datacom Systems Inc VS-1200 Data Acccess SwitchTable of Contents VS-1200 Series Functional Drawing Application Hardware InstallationCustomer Service Copyright License Agreement Trademark Attribution Terms of UseProprietary Notice Certifications and MarksSafety Notices and Warnings VS-1200 Series Summary OverviewWhat Shipped? VS-1200 Series Features and BenefitsVS-1200 Series Model Specific Specifications VS-1200 Series Common SpecificationsPower Consumption 12W BTU/h Operating Range Relative Humidity 5 to 90% non-condensingPage VS-1210BT/SFP HardwareVS-1200 Series Front Panels Any-to-Any Ports PowerFront Panel Description Management Port Rear Panel DescriptionInput Power Power Switch SFP seriesSerial DB9 Rear Label BT seriesBasic Functionality Initial ConfigurationCommand Line Interface CLI Basic Commands Read Only Access Password RecoverySET Port Monitor SE PO MO TAP Show Groups SH GR Group NameShow Port Routing SH PO RO Show Users SH US Superuser Commands Configuration AccessSU SET Password SU SE PA SET Date Mmddyy # SET IP Subnet Gateway# SE PO MO 3 OFF SET Time HhmmssADD User AD US HyperTerminal Serial Port Configuration DB9Delete User Username Port Number Management Port Configuration RJ45TCP/IP Winsock Telnet IP Address ConfigurationIP Address Configuration with HyperTerminal Accessories Communications HyperTerminal VS-1200 Data Acccess Switch Initial Configuration IP Address Configuration with Telnet Network Connections Accessories Command Prompt Initial Configuration Exercise CLI Setting Ports Initial Configuration # SET Port Monitor 2 from 8,9 # SET Port Monitor 1 from 7,9# SET Port Monitor 6 from 3,4 # SET Port Monitor 5 from# SET Port Monitor 7 from # SET Port Monitor 8 fromIntallation Prerequisites Safety GuidelinesSmall Form-Factor Plug Module Removing the SFP Module Installing the SFP ModulePage Any-to-Any Connection Hardware InstallationPower Management Connection VS-1210BT-BT/SFP VS-1200 Series Functional DrawingVS-1204BT VS-1204SFP Application Gathering the Data HyperTerminal configuration exampleVS-1200 Data Acccess Switch # SET Port Monitor 9 from # SET Port Monitor 4 from# SET Port Monitor 6 from VS-1200 Data Acccess Switch Application # SET Port Monitor 6 from 1,3 # SET Port Monitor 5 from 1,3# SET Port Monitor 7 from 2,4 # SET Port Monitor 8 from 2,4Limits of Liability Customer ServiceInternet Warranty Datacom Systems Inc
Top Page Image Contents