Datacom Systems VS-1200 manual Initial Configuration

Page 37

Initial Configuration

37

GOAL/SOLUTION: The exercise for the setup of a VS-1210BT/SFP shown is as follows:

∙Ports 1, 2, 3 and 4 have been setup as inputs.

∙Port 5 has been setup to output data to a Network IDS from Port 4’s input.

∙Port 6 has been setup to output aggregated data to a Probe from Port 3 and 4’s inputs.

∙Port 7 has been setup to output data to a Network IDS from Port 1’s input and returns TCP resets from the Network IDS.

∙Port 8 has been setup to output data to a Network IDS from Port 2’s input and returns TCP resets from the Network IDS.

∙Port 9 has been setup to output aggregated data to a Network IDS from Port 1 and 2’s inputs/ outputs and returns TCP resets from the Network IDS.

∙Port 10 has been setup to output aggregated data to a Probe from Port 1, 2, 3, and 4’s inputs.

NOTE: Port 9’s Network IDS’s network interface card (NIC) can handle both sides of the network conversation at once. Port 7 and 8’s Network IDS’s network interface cards cannot handle the whole conversation at once and must use two separate NICs for each side of the conversation. It can be setup either way to fit your network devices/tools’ requirements.

CONFIGURATION: For the connections to be properly set, use the syntax below in the Command Line Interface (CLI) to setup Any-to-Any ports. As the IP address (default 192.168.1.1) is set during the 'Initial Configuration' it is not covered in this section, see the 'IP Address 28 ' section for those steps. The connections in this exercise are setup in the CLI as shown below (syntax is shown with either user > or Superuser # prompts):

For Initial Configuration, open HyperTerminal on your Management PC using the VS-1210BT/SFP SERIAL DB9 port. Settings are found in the 'Initial Configuration', 'SERIAL Port Configuration (DB9)', 'HyperTerminal 26 ' section.

Press Enter key, Enter key, then enter your Username (default: Administrator), Enter key,

Password (default: admin) and Enter key. Default prompt is the > symbol.

© 2009 Datacom Systems Inc

Image 37

Contents USERguide Page Product Description Datacom Systems Inc VS-1200 Data Acccess SwitchTable of Contents Customer Service Hardware InstallationVS-1200 Series Functional Drawing Application Copyright License Agreement Trademark Attribution Terms of UseProprietary Notice Certifications and MarksSafety Notices and Warnings VS-1200 Series Summary OverviewWhat Shipped? VS-1200 Series Features and BenefitsVS-1200 Series Model Specific Specifications VS-1200 Series Common SpecificationsPower Consumption 12W BTU/h Operating Range Relative Humidity 5 to 90% non-condensingPage VS-1200 Series Front Panels HardwareVS-1210BT/SFP Front Panel Description PowerAny-to-Any Ports Management Port Rear Panel DescriptionInput Power Power Switch SFP seriesSerial DB9 Rear Label BT seriesCommand Line Interface CLI Initial ConfigurationBasic Functionality Basic Commands Read Only Access Password RecoverySET Port Monitor SE PO MO TAP Show Groups SH GR Group NameShow Port Routing SH PO RO SU SET Password SU SE PA Superuser Commands Configuration AccessShow Users SH US SET Date Mmddyy # SET IP Subnet Gateway# SE PO MO 3 OFF SET Time HhmmssADD User AD US Delete User Username Serial Port Configuration DB9HyperTerminal TCP/IP Winsock Management Port Configuration RJ45Port Number IP Address Configuration with HyperTerminal IP Address ConfigurationTelnet Accessories Communications HyperTerminal VS-1200 Data Acccess Switch Initial Configuration IP Address Configuration with Telnet Network Connections Accessories Command Prompt Initial Configuration Exercise CLI Setting Ports Initial Configuration # SET Port Monitor 2 from 8,9 # SET Port Monitor 1 from 7,9# SET Port Monitor 6 from 3,4 # SET Port Monitor 5 from# SET Port Monitor 7 from # SET Port Monitor 8 fromSmall Form-Factor Plug Module Safety GuidelinesIntallation Prerequisites Removing the SFP Module Installing the SFP ModulePage Power Hardware InstallationAny-to-Any Connection Management Connection VS-1210BT-BT/SFP VS-1200 Series Functional DrawingVS-1204BT VS-1204SFP Application Gathering the Data HyperTerminal configuration exampleVS-1200 Data Acccess Switch # SET Port Monitor 6 from # SET Port Monitor 4 from# SET Port Monitor 9 from VS-1200 Data Acccess Switch Application # SET Port Monitor 6 from 1,3 # SET Port Monitor 5 from 1,3# SET Port Monitor 7 from 2,4 # SET Port Monitor 8 from 2,4Internet Warranty Customer ServiceLimits of Liability Datacom Systems Inc