Axis Communications A1001 user manual Verify the Hardware Connections, Set the Date and Time

Page 17

AXIS A1001 Network Door Controller & AXIS Entry Manager

System Configuration

1.Install end of line resistors on all the used inputs. See the connection diagram on page 62.

2.Go to Setup > Hardware Reconfiguration and select Enable supervised inputs. You can also enable supervised inputs during the hardware configuration.

Supervised Input Compatibility

The following connectors support supervised inputs:

Reader I/O connector – tampering signal. See page 58.

Door connector. See page 59.

Readers and switches that can be used with supervised inputs include:

HID readers with internal 1 kΩ pull-up to 5 V.

Readers and switches with internal 1 kΩ pull-up to 5 V.

Readers and switches without internal pull-up.

Verify the Hardware Connections

When the hardware installation and configuration is complete, and anytime during the door controller’s lifetime, you can verify the function of the connected door monitors, locks and readers.

To verify the configuration and access the verification controls, go to Setup > Hardware Connection Verification .

Verification Controls

Door state – Verify the current state of the door monitor, door alarms and locks. Click Get current state.

Lock – Manually trigger the lock. Both primary locks and secondary locks if there are any will be affected. Click Lock or Unlock.

Lock – Manually trigger the lock to grant access. Only primary locks will be affected. Click Access.

Reader: Feedback – Verify the reader feedback, for example sounds and LED signals, for different commands. Select the command and click Test. Which types of feedback that are available depends on the reader. For more information, see Reader Feedback. See also the manufacturer’s instructions.

Reader: Tampering – Get information about the last tampering attempt. The first tampering attempt will be registered when the reader is installed. Click Get last tampering.

Reader: Card swipe – Get information about the last swiped card or other type of user token accepted by the reader. Click Get last credential.

REX – Get information about the last time the request to exit (REX) device was pressed. Click Get last REX.

Set the Date and Time

If the door controller is part of a system, the date and time settings will be distributed to all the door controllers. This means that the settings are pushed to the other controllers in the system, regardless of whether you synchronize with an NTP server, set the date and time manually, or get the date and time from the computer. If you cannot see the changes, try refreshing the page in your browser.

For more information about managing a system of door controllers, see Manage Network Door Controllers on page 21.

To set the date and time of the Axis product, go to Setup > Date & Time.

You can set the date and time in the following ways:

• Get the date and time from a network time protocol (NTP) server. See page 18.

17

Image 17
Contents Axis A1001 Network Door Controller & Axis Entry Manager Liability About this DocumentIntellectual Property Rights Equipment Modifications Trademark AcknowledgmentsLearn More SupportAxis A1001 Network Door Controller & Axis Entry Manager Front and back Hardware OverviewInterface External power inputsPower outputs Color Indication LED IndicatorsLED indicators, buttons and other hardware External Power Inputs Connectors and ButtonsFor technical specifications, see Power ConnectorButtons and Other Hardware Power OutputsAccess from the Internet Access from a BrowserSet the Root Password Start a browser Chrome, Internet Explorer, Firefox, SafariOverview Select a Language Configuration Step by StepImport a Hardware Configuration File Configure the HardwareExport a Hardware Configuration File To import a hardware configuration fileConfigure Locks and Door Monitors Create a New Hardware ConfigurationTo create a new hardware configuration from the beginning Motorized locks must be configured as secondary locksLock Options Use Supervised Inputs Configure Readers and REX DevicesReader and REX Device Options Following reader options are availableVerification Controls Verify the Hardware ConnectionsSet the Date and Time Get the Date and Time from the Computer Configure the Network SettingsSet the Date and Time Manually Basic TCP/IP Settings Configure Card FormatsTo enable card formats Go to Setup Configure Card FormatsField Maps Card Format DescriptionsDoor Controller System Status Manage Network Door ControllersConnected Door Controllers in the System Connected Door Controllers ListRemove Door Controllers from the System Click Reset hardware configurationIP address MAC address Maintenance Instructions Choose a Workflow Access ManagementAbout Users Access Schedule Types Create and Edit Access SchedulesAdd Schedule Items Create and Edit Groups Go to Access Management Groups tab, click Add new groupManage Doors Group CredentialsClick Add scheduled unlock Identification TypesAdd Scheduled Unlock States Create and Edit Users Go to Access ManagementUse Manual Door Actions Manual Door ActionsImport Users User CredentialsFollowing credentials are available for users First name required Last nameExport Users Example Access Schedule CombinationsCreate a Subtraction schedule called Nights & weekends Configure the Event and Alarm Logs View the Alarm LogView the Event Log Event Log FiltersEvent Log Options Set Up Action RulesAlarm Log Options Configuration Access PointTriggers Go to Events Action Rules and click AddHardware DoorAdd Recipients ActionsCreate Schedules Set Up Email RecipientsRecipient Types Following recipients are availableReader Feedback Set Up RecurrencesEvent Wiegand Beeper pattern State Dual LED Single LEDReport Types View, Print, and Export ReportsClick View and print Click Print selected columnsSecurity To enable Https on the Axis productUsers IP Address FilterCertificates To allow the product to access a network protected by IeeeIeee Date & Time Click Install certificate and upload the certificateNetwork Create a self-signed certificate as described aboveARP/Ping Assign IP Address Using ARP/PingLinux/Unix syntax Linux/Unix exampleAxis Internet Dynamic DNS Service Advanced TCP/IP SettingsDNS Configuration NTP ConfigurationLink-Local IPv4 Address Host Name ConfigurationInformation, see the online help QoS Quality of ServicePorts & Devices MaintenanceSupport Overview SupportSystem Overview Logs & ReportsAdvanced Reset to Factory Default SettingsScripting File UploadEmergency Recovery Procedure Upgrade the FirmwareFirmware To upgrade the product’s firmware UNIX/Linux, type the following from the command lineProblems setting the IP address Symptoms, Possible Causes and Remedial ActionsProduct cannot be accessed from a browser Product is accessible locally but not externallyHardware failure Status and Network indicator LEDs are flashing red rapidlyAxis A1001 Network Door Controller Power Function/group Specifications General CasingConnectors WeightAxis Entry Manager Connectors Reader I/O Connector Reader Data ConnectorFunction Pin Specifications Function PinPower Connector Door ConnectorAuxiliary Connector Power Lock Connector Network ConnectorPower & Relay Connector Tampering Alarm Pin HeaderBack tampering alarm Connection DiagramsSupervised Inputs M5.7
Related manuals
Manual 20 pages 40.35 Kb