Axis Communications A1001 user manual Reader Data Connector, Reader I/O Connector, Function Pin

Page 58

AXIS A1001 Network Door Controller & AXIS Entry Manager

Technical Specifications

Reader Data Connector

6-pin terminal block supporting RS485 and Wiegand protocols for communication with the reader.

The RS485 ports support:

•Two-wire RS485 half duplex

•Four-wire RS485 full duplex

The Wiegand ports support:

• Two-wire Wiegand

Function		Pin	Notes

RS485	A-	1	For full duplex RS485
			For half duplex RS485
	B+	2	For half duplex RS485
	B+	2

RS485	A-	3	For full duplex RS485
			For half duplex RS485
	B+	4	For half duplex RS485
	B+	4

Wiegand	D0 (Data 0)	5	For Wiegand

	D1 (Data 1)	6

Important

The recommended maximum cable length is 30 m (98.4 ft).

Reader I/O Connector

6-pin terminal block for:

•Auxiliary power (DC output)

•Digital Input

•Digital Output

•0 V DC (-)

Pin 3 on the reader I/O connectors can be supervised. If the connection is interrupted, an event is activated. To use supervised inputs, install end of line resistors. Use the connection diagram for supervised inputs. See page 62.

Function	Pin	Notes	Specifications

0 V DC (-)	1		0 V DC

DC output	2	For powering auxiliary equipment.	12 V DC
		Note: This pin can only be used as power out.	Max load = 300 mA

Configurable (Input	3–6	Digital input — Connect to pin 1 to activate, or leave	0 to max 40 V DC
or Output)		floating (unconnected) to deactivate.
		Digital output — Connect to pin 1 to activate, or leave	0 to max 40 V DC, open drain,
		floating (unconnected) to deactivate. If used with an	100 mA
		inductive load, e.g. a relay, a diode must be connected
		in parallel with the load, for protection against voltage
		transients.

58

Image 58

Contents Axis A1001 Network Door Controller & Axis Entry Manager Intellectual Property Rights Equipment Modifications About this DocumentLiability Trademark AcknowledgmentsSupport Learn MoreAxis A1001 Network Door Controller & Axis Entry Manager Hardware Overview Front and backPower outputs External power inputsInterface LED indicators, buttons and other hardware LED IndicatorsColor Indication For technical specifications, see Connectors and ButtonsExternal Power Inputs Power ConnectorPower Outputs Buttons and Other HardwareSet the Root Password Access from a BrowserAccess from the Internet Start a browser Chrome, Internet Explorer, Firefox, SafariOverview Configuration Step by Step Select a LanguageExport a Hardware Configuration File Configure the HardwareImport a Hardware Configuration File To import a hardware configuration fileTo create a new hardware configuration from the beginning Create a New Hardware ConfigurationConfigure Locks and Door Monitors Motorized locks must be configured as secondary locksLock Options Reader and REX Device Options Configure Readers and REX DevicesUse Supervised Inputs Following reader options are availableSet the Date and Time Verify the Hardware ConnectionsVerification Controls Set the Date and Time Manually Configure the Network SettingsGet the Date and Time from the Computer To enable card formats Configure Card FormatsBasic TCP/IP Settings Go to Setup Configure Card FormatsCard Format Descriptions Field MapsConnected Door Controllers in the System Manage Network Door ControllersDoor Controller System Status Connected Door Controllers ListIP address MAC address Click Reset hardware configurationRemove Door Controllers from the System Maintenance Instructions About Users Access ManagementChoose a Workflow Create and Edit Access Schedules Access Schedule TypesAdd Schedule Items Manage Doors Go to Access Management Groups tab, click Add new groupCreate and Edit Groups Group CredentialsAdd Scheduled Unlock States Identification TypesClick Add scheduled unlock Use Manual Door Actions Go to Access ManagementCreate and Edit Users Manual Door ActionsFollowing credentials are available for users User CredentialsImport Users First name required Last nameExample Access Schedule Combinations Export UsersCreate a Subtraction schedule called Nights & weekends View the Event Log View the Alarm LogConfigure the Event and Alarm Logs Event Log FiltersAlarm Log Options Set Up Action RulesEvent Log Options Triggers Access PointConfiguration Go to Events Action Rules and click AddDoor HardwareActions Add RecipientsRecipient Types Set Up Email RecipientsCreate Schedules Following recipients are availableEvent Wiegand Set Up RecurrencesReader Feedback Beeper pattern State Dual LED Single LEDClick View and print View, Print, and Export ReportsReport Types Click Print selected columnsUsers To enable Https on the Axis productSecurity IP Address FilterIeee To allow the product to access a network protected by IeeeCertificates Network Click Install certificate and upload the certificateDate & Time Create a self-signed certificate as described aboveLinux/Unix syntax Assign IP Address Using ARP/PingARP/Ping Linux/Unix exampleDNS Configuration Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service NTP ConfigurationHost Name Configuration Link-Local IPv4 AddressQoS Quality of Service Information, see the online helpMaintenance Ports & DevicesSystem Overview SupportSupport Overview Logs & ReportsScripting Reset to Factory Default SettingsAdvanced File UploadFirmware To upgrade the product’s firmware Upgrade the FirmwareEmergency Recovery Procedure UNIX/Linux, type the following from the command lineProduct cannot be accessed from a browser Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product is accessible locally but not externallyStatus and Network indicator LEDs are flashing red rapidly Hardware failureAxis A1001 Network Door Controller Connectors Function/group Specifications General CasingPower WeightAxis Entry Manager Connectors Function Pin Specifications Reader Data ConnectorReader I/O Connector Function PinAuxiliary Connector Door ConnectorPower Connector Power & Relay Connector Network ConnectorPower Lock Connector Tampering Alarm Pin HeaderConnection Diagrams Back tampering alarmSupervised Inputs M5.7

Related manuals

Manual 20 pages 40.35 Kb