Axis Communications A1001 user manual Connectors and Buttons, Interface, External Power Inputs

Page 8

AXIS A1001 Network Door Controller & AXIS Entry Manager

Hardware Overview

Lock

Note

Green

Steady when not energized.

 

 

Red

Steady when energized.

 

 

Unlit

Floating.

 

 

•The Status LED can be configured to flash while an event is active.

•The Status LED can be configured to flash for identifying the unit. Go to Setup > Additional Controller Configuration > System Options > Maintenance .

Connectors and Buttons

For technical specifications, see page 54.

I/O Interface

Reader Data Connector

Two 6-pin terminal blocks supporting RS485 and Wiegand protocols for communication with the reader. For specifications, see page 58.

Reader I/O Connector

Two 6-pin terminal blocks for reader input and output. In addition to the 0 V DC reference point and power (DC output), the reader I/O connector provides the interface to:

•Digital input – For connecting, for example, reader tampering alarms.

•Digital output – For connecting, for example, reader beepers and reader LEDs. For specifications, see page 58.

Door Connector

Two 4-pin terminal blocks for connecting door monitoring devices and request to exit (REX) devices. For specifications, see page 59.

Auxiliary Connector

4-pin configurable I/O terminal block. Use with external devices, in combination with, for example tampering alarms, event triggering and alarm notifications. In addition to the 0 V DC reference point and power (DC output), the auxiliary connector provides the interface to:

•Digital input – An alarm input for connecting devices that can toggle between an open and closed circuit, for example PIR sensors or glass break detectors.

•Digital output – For connecting external devices such as burglar alarms, sirens or lights. Connected devices can be activated by the VAPIX® application programming interface or by an action rule.

For specifications, see page 59.

External Power Inputs

NOTICE

The product shall be connected using a shielded network cable (STP). All cables connecting the product to the network shall be intended for their specific use. Make sure that the network devices are installed in accordance with the manufacturer’s instructions. For information about regulatory requirements, see Electromagnetic Compatibility (EMC) on page 2 .

Power Connector

2-pin terminal block for DC power input. Use a Safety Extra Low Voltage (SELV) compliant limited power source (LPS) with either a rated output power limited to ≤100 W or a rated output current limited to ≤5 A. For specifications, see page 59.

Network Connector

RJ45 Ethernet connector. Supports Power over Ethernet (PoE). For specifications, see page 60.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Axis A1001 Network Door Controller & Axis Entry Manager About this Document LiabilityIntellectual Property Rights Equipment Modifications Trademark AcknowledgmentsSupport Learn MoreAxis A1001 Network Door Controller & Axis Entry Manager Hardware Overview Front and backInterface External power inputsPower outputs Color Indication LED IndicatorsLED indicators, buttons and other hardware Connectors and Buttons External Power InputsFor technical specifications, see Power ConnectorPower Outputs Buttons and Other HardwareAccess from a Browser Access from the InternetSet the Root Password Start a browser Chrome, Internet Explorer, Firefox, SafariOverview Configuration Step by Step Select a LanguageConfigure the Hardware Import a Hardware Configuration FileExport a Hardware Configuration File To import a hardware configuration fileCreate a New Hardware Configuration Configure Locks and Door MonitorsTo create a new hardware configuration from the beginning Motorized locks must be configured as secondary locksLock Options Configure Readers and REX Devices Use Supervised InputsReader and REX Device Options Following reader options are availableVerification Controls Verify the Hardware ConnectionsSet the Date and Time Get the Date and Time from the Computer Configure the Network SettingsSet the Date and Time Manually Configure Card Formats Basic TCP/IP SettingsTo enable card formats Go to Setup Configure Card FormatsCard Format Descriptions Field MapsManage Network Door Controllers Door Controller System StatusConnected Door Controllers in the System Connected Door Controllers ListRemove Door Controllers from the System Click Reset hardware configurationIP address MAC address Maintenance Instructions Choose a Workflow Access ManagementAbout Users Create and Edit Access Schedules Access Schedule TypesAdd Schedule Items Go to Access Management Groups tab, click Add new group Create and Edit GroupsManage Doors Group CredentialsClick Add scheduled unlock Identification TypesAdd Scheduled Unlock States Go to Access Management Create and Edit UsersUse Manual Door Actions Manual Door ActionsUser Credentials Import UsersFollowing credentials are available for users First name required Last nameExample Access Schedule Combinations Export UsersCreate a Subtraction schedule called Nights & weekends View the Alarm Log Configure the Event and Alarm LogsView the Event Log Event Log FiltersEvent Log Options Set Up Action RulesAlarm Log Options Access Point ConfigurationTriggers Go to Events Action Rules and click AddDoor HardwareActions Add RecipientsSet Up Email Recipients Create SchedulesRecipient Types Following recipients are availableSet Up Recurrences Reader FeedbackEvent Wiegand Beeper pattern State Dual LED Single LEDView, Print, and Export Reports Report TypesClick View and print Click Print selected columnsTo enable Https on the Axis product SecurityUsers IP Address FilterCertificates To allow the product to access a network protected by IeeeIeee Click Install certificate and upload the certificate Date & TimeNetwork Create a self-signed certificate as described aboveAssign IP Address Using ARP/Ping ARP/PingLinux/Unix syntax Linux/Unix exampleAdvanced TCP/IP Settings Axis Internet Dynamic DNS ServiceDNS Configuration NTP ConfigurationHost Name Configuration Link-Local IPv4 AddressQoS Quality of Service Information, see the online helpMaintenance Ports & DevicesSupport Support OverviewSystem Overview Logs & ReportsReset to Factory Default Settings AdvancedScripting File UploadUpgrade the Firmware Emergency Recovery ProcedureFirmware To upgrade the product’s firmware UNIX/Linux, type the following from the command lineSymptoms, Possible Causes and Remedial Actions Problems setting the IP addressProduct cannot be accessed from a browser Product is accessible locally but not externallyStatus and Network indicator LEDs are flashing red rapidly Hardware failureAxis A1001 Network Door Controller Function/group Specifications General Casing PowerConnectors WeightAxis Entry Manager Connectors Reader Data Connector Reader I/O ConnectorFunction Pin Specifications Function PinPower Connector Door ConnectorAuxiliary Connector Network Connector Power Lock ConnectorPower & Relay Connector Tampering Alarm Pin HeaderConnection Diagrams Back tampering alarmSupervised Inputs M5.7
Related manuals
Manual 20 pages 40.35 Kb
Top Page Image Contents