Bay Technical Associates V80 PDI-2, V79 PDI-1 owner manual Front Panel Configuration

Page 36

5.3FRONT PANEL CONFIGURATION

The LCD display and associated front panel controls can provide the configuration status of the PDI. All the parameters shown in the LCD status message are fully described in Section 5.1.

When the M8/M16 DAC has completed its power-up self-test, the following menu will be displayed on the LCD:

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿Bay Technical Assoc ￿

￿ ￿

￿ Select Module ￿

￿ 00 ￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

NOTE: The following LCD screens are examples and will vary depending upon current configuration status.

To review the configuration status of the PDI installed as Module XX (XX = 02 to 16), use the > or ? keys to highlight "Module XX" from the M Series main menu screen and press the SELECT key. The LCD will respond with a menu similar to the following for the PDI-1:

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿V78 PDI-1 MODULE XX￿

￿ ￿

￿Display Status ￿

￿Exit Module Menus ￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

Select "Display Status" the LCD will respond with:

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿Debounce Delay 10 ￿

￿Latch Polarity HI/LO ￿

￿Report Method COMMAND￿

￿76-PAGE SELECT-EXIT ￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

Pressing the > or ? keys scrolls through the following entries:

Report Interval HH:MM

Host Address 1:1,1

Time Tagging ENABLE

Term Charac ters 0D0A

Dyna Cfg Cmd ENABLE

To exit the configuration status mode, press the SELECT key at any time. You are returned to the PDI's LCD main menu. Next, press either arrow key until the cursor is located on the "Exit Module Menus." Pressing the SELECT button returns you to the main M Series LCD menu.

32

Page 35 Page 37
Image 36
Page 35 Page 37
Contents BayTech Publication #U140E105 Page Table of Contents Reporting Method General V79 PDI-1 Module Specifications V79 PDI-1 Switch Input Status Module V80 PDI-2 Optically Isolated Input Module Installation CablingPDI-2 AC Input Setup Operation USER-PROGRAMMABLE Features Sampling SetupReporting Setup Reporting MethodReport Start Time Report IntervalHost Address Dynamic Configuration Data CommandsTerminating Characters Take a single sample for Ports Clear Event Buffer Command Clear Event Counter CommandClear Event Latch Data Report ALL Buffered Events Command Report Event Counter CommandReport Event Duration Command Report Event Latch Data Command Report Event Counter and Reset CommandReport Event Latch Data and Reset Command Report a Single Buffered Event Command Event Sample ReportingPage Event Sample Presentation 115,1 1320 11/18/93 Configuration MENU-DRIVEN ConfigurationPage Configuration Main Menu Module Status SET Latch Polarity Select Reporting Method Report Start Time Report Interval Enable / Disable Time Tagging Dynamic Configuration Commands Exit Dynamic Configuration Procedure and Commands Debounce Delay Command Reporting Method CommandTime TAG Command Front Panel Configuration Appendix a DATA/CONFIGURATION Command Summary Appendix B Eprom Upgrade Appendix C V79 PDI-1 Mechanical Layout Page Page Appendix D V80 PDI-2 Mechanical Layout Page Page Appendix E Index Fifo Page
Top Page Image Contents