Datamax E-4204, E-4203, E-4304e manual Optional Features, Adjustable Media Sensor

Page 13

1.1.2 Optional Features

Adjustable Media Sensor

The Adjustable Media Sensor allows the printer to detect the position of the gap, notch, or reflective mark at many locations across the media.

External Media Supply Stand

The External Media Supply Stand allows the printer to use large media supply rolls, up to 8-inches in diameter and wound on one to three inch cores. (Not available for the E-4304.)

FLASH Memory Expansion

The FLASH Expansion cartridges are used for permanent storage of custom fonts, formats and graphics. The FLASH memory cartridges cannot be used in conjunction with the ILPC option.

Heavy Duty Power Supply

The Heavy Duty Power Supply is available for use in high demand applications. This power supply will also increase the E-4203’s print speed capability to 4 IPS.

ILPC

The International Language Print Capability consisting of one of the following:

¾CG-Times (western European) Scalable font

¾Kanji Gothic B Scalable font

¾Simplified Chinese GB Scalable font

Media Cutter

The Media Cutter automatically cuts your tag or label media after printing. This device mounts easily onto the front of the printer.

E-4203/E-4204/E-4304

3

Image 13

Contents Operator’s Manual Page Copyright Information Agency Compliance and Approvals Important Safety Instructions Page Printer Overview Troubleshooting Appendix a Page Introduction About this Printer Standard FeaturesAdjustable Media Sensor Optional FeaturesPresent Sensor Removing the Packaging Before Using the PrinterAdditional Requirements Inspecting the PrinterPower Connection Connecting the PrinterInterface Cables Interface ConnectionAdjusting the Media Sensor Die-cut Near the center of the label Gap Page Loading Media 4203/E-4204/E-4304 Loading Media for Peel Configuration Loading Ribbon 4203/E-4204/E-4304 Flash Memory Expansion 4203/E-4204/E-4304 Lights Buttons Normal Mode Button FunctionsTo change Printer Setup Printer Setup Mode Button FunctionsValues Menu Numbers Items Printer Setup Menu ListMedia Type Sensor Type Menu Items and ValuesControl Codes Form Length Align Length Stop Location Step by Step Modification of the Printer Setup New 19200 Baud Rate Label Alignment = YES Label AlignmentLabel Alignment = no Label Alignment = AutoProblem Possible Cause Solution Label Alignment Troubleshooting~OR~ ~OR~ ~OR~ To perform Calibration Calibration Mode Button FunctionsAuto Media Sensor Calibration Manual Media Sensor Calibration Internal Labels Database Configuration and Dot Check LabelsGood Dot Check Label Hex Dump Label Test LabelTo exit the Hex Dump Mode Area Method Interval Cleaning the Printhead Media Width Adjustment Ribbon Width Adjustment Fine Printhead Adjustment Removal Printhead ReplacementResetting to the Factory Defaults Darkness AdjustmentDownloading Firmware and Fonts Paused Light will flash during the download Problem Situation Troubleshooting TipsUnacceptable print quality Skips every other label Label advances 1-2 inches before a fault indication Printing MechanicalCommunications Media/RibbonFonts Embedded Bar CodesDesignator Description Maximum1 Minimum1 Approved Media4203/E-4204/E-4304 Ascii Control Code Chart XON Font Valid Ascii Characters decimal Use with Record Embedded Fonts and BarcodesAlphanumeric, upper and lower Font 6 62-character alphanumeric, uppercase 4203/E-4204/E-4304 Bar Code Type Length Check Valid Ascii Characters Sum BarcodesFIM Barcode a Code 3 Barcode I Codabar Kmart NON EDI Barcode T Telepen Printer Datamax Barcode Products Limited Warranty StatementThermal Printhead Warranty Service ProceduresLimitation of Liability General Warranty Provisions4203/E-4204/E-4304 Glossary 4203/E-4204/E-4304 4203/E-4204/E-4304 4203/E-4204/E-4304 4203/E-4204/E-4304 4203/E-4204/E-4304 Index Memory, 17, 24, 25, 27, 37, 38 Ribbon, 15, 16, 23, 44, 50, 52, 54, 55, 73, 76 4203/E-4204/E-4304