Datamax E-4204, E-4203, E-4304e manual Loading Media

Page 22

2.Use a finger to move the Bottom Slide until your selected Reference Letter appears in the Setting Window of the slide.

3.Use a finger to move the Top Slide until your selected Reference Letter appears in the Setting Window of the slide.

;Note: The Top and Bottom Slides must be positioned over the same Reference Letter for proper media sensor function.

4.Proceed to ‘Loading Media’ (Section 3.3).

3.3Loading Media

Load media into the printer as follows:

1.With the Cover open and the Printhead Carrier Assembly raised, remove the Media Hub and insert it through the Roll Media (with the labels spilling forward).

2.Place the Media Hub Flange (with its smooth side toward the media) onto the Media Hub.

3.Place the Media Hub, flange, and media onto the Standoffs in the printer.

Roll

Media

Printhead Carrier

Media Hub Flange

(smooth side toward media)

Media

Hub

Standoff

Printhead

Latch

4. Route the media through the printer, as shown below.

12	E-4203/E-4204/E-4304

Image 22

Contents Operator’s Manual Page Copyright Information Agency Compliance and Approvals Important Safety Instructions Page Printer Overview Troubleshooting Appendix a Page Introduction Standard Features About this PrinterOptional Features Adjustable Media SensorPresent Sensor Before Using the Printer Removing the PackagingInspecting the Printer Additional RequirementsConnecting the Printer Power ConnectionInterface Connection Interface CablesAdjusting the Media Sensor Die-cut Near the center of the label Gap Page Loading Media 4203/E-4204/E-4304 Loading Media for Peel Configuration Loading Ribbon 4203/E-4204/E-4304 Flash Memory Expansion 4203/E-4204/E-4304 Lights Normal Mode Button Functions ButtonsPrinter Setup Mode Button Functions To change Printer SetupPrinter Setup Menu List Values Menu Numbers ItemsMenu Items and Values Media Type Sensor TypeControl Codes Form Length Align Length Stop Location Step by Step Modification of the Printer Setup New 19200 Baud Rate Label Alignment Label Alignment = YESLabel Alignment = Auto Label Alignment = noLabel Alignment Troubleshooting Problem Possible Cause Solution~OR~ ~OR~ ~OR~ Calibration Mode Button Functions To perform CalibrationAuto Media Sensor Calibration Manual Media Sensor Calibration Database Configuration and Dot Check Labels Internal LabelsGood Dot Check Label Test Label Hex Dump LabelTo exit the Hex Dump Mode Area Method Interval Cleaning the Printhead Media Width Adjustment Ribbon Width Adjustment Fine Printhead Adjustment Printhead Replacement RemovalResetting to the Factory Defaults Darkness AdjustmentDownloading Firmware and Fonts Paused Light will flash during the download Troubleshooting Tips Problem SituationUnacceptable print quality Skips every other label Label advances 1-2 inches before a fault indication Mechanical PrintingFonts Media/RibbonCommunications Embedded Bar CodesApproved Media Designator Description Maximum1 Minimum14203/E-4204/E-4304 Ascii Control Code Chart XON Embedded Fonts and Barcodes Font Valid Ascii Characters decimal Use with RecordAlphanumeric, upper and lower Font 6 62-character alphanumeric, uppercase 4203/E-4204/E-4304 Barcodes Bar Code Type Length Check Valid Ascii Characters SumFIM Barcode a Code 3 Barcode I Codabar Kmart NON EDI Barcode T Telepen Datamax Barcode Products Limited Warranty Statement PrinterWarranty Service Procedures Thermal PrintheadGeneral Warranty Provisions Limitation of Liability4203/E-4204/E-4304 Glossary 4203/E-4204/E-4304 4203/E-4204/E-4304 4203/E-4204/E-4304 4203/E-4204/E-4304 4203/E-4204/E-4304 Index Memory, 17, 24, 25, 27, 37, 38 Ribbon, 15, 16, 23, 44, 50, 52, 54, 55, 73, 76 4203/E-4204/E-4304