Datamax E-4204, E-4203, E-4304e Label Alignment Troubleshooting, Problem Possible Cause Solution

Page 40

4.5.4 Label Alignment Troubleshooting

If you experience label alignment problems, the following table offers possible causes and solutions.

	Problem	Possible Cause	Solution
	Attempting to	With the Present	¾ Set Label Alignment to AUTO,
	perform Label	Sensor enabled,	press and hold FEED until
	Alignment	Label Alignment	media moves for the automatic
	results in no	cannot be	length measurement.
	paper	performed without	~OR~
	movement.	a Label Length.	~OR~
	movement.	a Label Length.	¾ Re-measure the Label
			¾ Re-measure the Label
			Alignment Length. Use Printer
			Setup mode to enter the new
			length. Print a Database
			Configuration label to ensure
			the new length has been set.

30	E-4203/E-4204/E-4304

Image 40

Contents Operator’s Manual Page Copyright Information Agency Compliance and Approvals Important Safety Instructions Page Printer Overview Troubleshooting Appendix a Page Introduction Standard Features About this PrinterOptional Features Adjustable Media SensorPresent Sensor Before Using the Printer Removing the PackagingInspecting the Printer Additional RequirementsConnecting the Printer Power ConnectionInterface Connection Interface CablesAdjusting the Media Sensor Die-cut Near the center of the label Gap Page Loading Media 4203/E-4204/E-4304 Loading Media for Peel Configuration Loading Ribbon 4203/E-4204/E-4304 Flash Memory Expansion 4203/E-4204/E-4304 Lights Normal Mode Button Functions ButtonsPrinter Setup Mode Button Functions To change Printer SetupPrinter Setup Menu List Values Menu Numbers ItemsMenu Items and Values Media Type Sensor TypeControl Codes Form Length Align Length Stop Location Step by Step Modification of the Printer Setup New 19200 Baud Rate Label Alignment Label Alignment = YESLabel Alignment = Auto Label Alignment = noLabel Alignment Troubleshooting Problem Possible Cause Solution~OR~ ~OR~ ~OR~ Calibration Mode Button Functions To perform CalibrationAuto Media Sensor Calibration Manual Media Sensor Calibration Database Configuration and Dot Check Labels Internal LabelsGood Dot Check Label Test Label Hex Dump LabelTo exit the Hex Dump Mode Area Method Interval Cleaning the Printhead Media Width Adjustment Ribbon Width Adjustment Fine Printhead Adjustment Printhead Replacement RemovalResetting to the Factory Defaults Darkness AdjustmentDownloading Firmware and Fonts Paused Light will flash during the download Troubleshooting Tips Problem SituationUnacceptable print quality Skips every other label Label advances 1-2 inches before a fault indication Mechanical PrintingMedia/Ribbon CommunicationsFonts Embedded Bar CodesApproved Media Designator Description Maximum1 Minimum14203/E-4204/E-4304 Ascii Control Code Chart XON Embedded Fonts and Barcodes Font Valid Ascii Characters decimal Use with RecordAlphanumeric, upper and lower Font 6 62-character alphanumeric, uppercase 4203/E-4204/E-4304 Barcodes Bar Code Type Length Check Valid Ascii Characters SumFIM Barcode a Code 3 Barcode I Codabar Kmart NON EDI Barcode T Telepen Datamax Barcode Products Limited Warranty Statement PrinterWarranty Service Procedures Thermal PrintheadGeneral Warranty Provisions Limitation of Liability4203/E-4204/E-4304 Glossary 4203/E-4204/E-4304 4203/E-4204/E-4304 4203/E-4204/E-4304 4203/E-4204/E-4304 4203/E-4204/E-4304 Index Memory, 17, 24, 25, 27, 37, 38 Ribbon, 15, 16, 23, 44, 50, 52, 54, 55, 73, 76 4203/E-4204/E-4304