Datamax E-4204, E-4203, E-4304e manual Agency Compliance and Approvals

Page 4

Agency Compliance and Approvals:

UL1950 Information Technology Equipment

C22.2 No. 950-M93

CUS

Listed

EN60950

For 230 Volt Operation (Europe): Use a cord set, marked "HAR," consisting of a min H05VV-F cord which has a minimum 0.75 square mm diameter conductors, provided with an IEC 320 receptacle and a male plug for the country of installation rated 6A, 250V

Für 230 Volt (Europa): Benützen Sie ein Kabel, das mit "HAR" markiert ist, bestehend mindestens aus einem H05VV-F Kabel, das mindestens 0,75 Quadratmillimeter Drahtdurchmesser hat; sowie eine IEC320 Steckdose und einen für das Land geeigneten Stecker, 6A, 250 Volt.

As an Energy Star Partner, the manufacturer has determined that this product meets the Energy Star guidelines for energy efficiency.

The manufacturer declares under sole responsibility that this product conforms to the following standards or other normative documents:

EMC:

EN 55022

(1993) Class A

 

EN 50024

(1998)

Safety: This product complies with the requirements of EN 60950 /A11:1997

Gost-R

FCC: This device complies with FCC CFR 47 Part 15 Class A.

;Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions in this manual, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Image 4
Contents Operator’s Manual Page Copyright Information Agency Compliance and Approvals Important Safety Instructions Page Printer Overview Troubleshooting Appendix a Page Introduction Standard Features About this PrinterOptional Features Adjustable Media SensorPresent Sensor Before Using the Printer Removing the PackagingInspecting the Printer Additional RequirementsConnecting the Printer Power ConnectionInterface Connection Interface CablesAdjusting the Media Sensor Die-cut Near the center of the label Gap Page Loading Media 4203/E-4204/E-4304 Loading Media for Peel Configuration Loading Ribbon 4203/E-4204/E-4304 Flash Memory Expansion 4203/E-4204/E-4304 Lights Normal Mode Button Functions ButtonsPrinter Setup Mode Button Functions To change Printer SetupPrinter Setup Menu List Values Menu Numbers ItemsMenu Items and Values Media Type Sensor TypeControl Codes Form Length Align Length Stop Location Step by Step Modification of the Printer Setup New 19200 Baud Rate Label Alignment Label Alignment = YESLabel Alignment = Auto Label Alignment = noLabel Alignment Troubleshooting Problem Possible Cause Solution~OR~ ~OR~ ~OR~ Calibration Mode Button Functions To perform CalibrationAuto Media Sensor Calibration Manual Media Sensor Calibration Database Configuration and Dot Check Labels Internal LabelsGood Dot Check Label Test Label Hex Dump LabelTo exit the Hex Dump Mode Area Method Interval Cleaning the Printhead Media Width Adjustment Ribbon Width Adjustment Fine Printhead Adjustment Printhead Replacement RemovalResetting to the Factory Defaults Darkness AdjustmentDownloading Firmware and Fonts Paused Light will flash during the download Troubleshooting Tips Problem SituationUnacceptable print quality Skips every other label Label advances 1-2 inches before a fault indication Mechanical PrintingMedia/Ribbon CommunicationsFonts Embedded Bar CodesApproved Media Designator Description Maximum1 Minimum14203/E-4204/E-4304 Ascii Control Code Chart XON Embedded Fonts and Barcodes Font Valid Ascii Characters decimal Use with RecordAlphanumeric, upper and lower Font 6 62-character alphanumeric, uppercase 4203/E-4204/E-4304 Barcodes Bar Code Type Length Check Valid Ascii Characters SumFIM Barcode a Code 3 Barcode I Codabar Kmart NON EDI Barcode T Telepen Datamax Barcode Products Limited Warranty Statement PrinterWarranty Service Procedures Thermal PrintheadGeneral Warranty Provisions Limitation of Liability4203/E-4204/E-4304 Glossary 4203/E-4204/E-4304 4203/E-4204/E-4304 4203/E-4204/E-4304 4203/E-4204/E-4304 4203/E-4204/E-4304 Index Memory, 17, 24, 25, 27, 37, 38 Ribbon, 15, 16, 23, 44, 50, 52, 54, 55, 73, 76 4203/E-4204/E-4304