Datamax E-4203, E-4204, E-4304e manual

Page 21

Reference	Distance of the TOF Mark Distance from the Media Edge
Letter	(inches)	(millimeters)
A	.180	4.6
B	.500	12.7
C	.750	19.1
D	1.00	25.4
E	1.25	31.8
F	1.50	38.1
G	1.75	44.5
H	2.00	50.8
I	2.25	57.2
J	2.50	63.5
K	2.75	69.9
L	3.00	76.2

Position the Adjustable Media Sensor as follows:

1. Based on the measurement made earlier, choose the Reference Letter that best corresponds to the location of your TOF mark.

ReferenceLetters

Setting Window

Top Slide

Bottom Slide

Setting Window

Reference Letters

E-4203/E-4204/E-4304

11

Image 21

Contents Operator’s Manual Page Copyright Information Agency Compliance and Approvals Important Safety Instructions Page Printer Overview Troubleshooting Appendix a Page Introduction About this Printer Standard FeaturesAdjustable Media Sensor Optional FeaturesPresent Sensor Removing the Packaging Before Using the PrinterAdditional Requirements Inspecting the PrinterPower Connection Connecting the PrinterInterface Cables Interface ConnectionAdjusting the Media Sensor Die-cut Near the center of the label Gap Page Loading Media 4203/E-4204/E-4304 Loading Media for Peel Configuration Loading Ribbon 4203/E-4204/E-4304 Flash Memory Expansion 4203/E-4204/E-4304 Lights Buttons Normal Mode Button FunctionsTo change Printer Setup Printer Setup Mode Button FunctionsValues Menu Numbers Items Printer Setup Menu ListMedia Type Sensor Type Menu Items and ValuesControl Codes Form Length Align Length Stop Location Step by Step Modification of the Printer Setup New 19200 Baud Rate Label Alignment = YES Label AlignmentLabel Alignment = no Label Alignment = AutoProblem Possible Cause Solution Label Alignment Troubleshooting~OR~ ~OR~ ~OR~ To perform Calibration Calibration Mode Button FunctionsAuto Media Sensor Calibration Manual Media Sensor Calibration Internal Labels Database Configuration and Dot Check LabelsGood Dot Check Label Hex Dump Label Test LabelTo exit the Hex Dump Mode Area Method Interval Cleaning the Printhead Media Width Adjustment Ribbon Width Adjustment Fine Printhead Adjustment Removal Printhead ReplacementDarkness Adjustment Resetting to the Factory DefaultsDownloading Firmware and Fonts Paused Light will flash during the download Problem Situation Troubleshooting TipsUnacceptable print quality Skips every other label Label advances 1-2 inches before a fault indication Printing MechanicalCommunications Media/RibbonFonts Embedded Bar CodesDesignator Description Maximum1 Minimum1 Approved Media4203/E-4204/E-4304 Ascii Control Code Chart XON Font Valid Ascii Characters decimal Use with Record Embedded Fonts and BarcodesAlphanumeric, upper and lower Font 6 62-character alphanumeric, uppercase 4203/E-4204/E-4304 Bar Code Type Length Check Valid Ascii Characters Sum BarcodesFIM Barcode a Code 3 Barcode I Codabar Kmart NON EDI Barcode T Telepen Printer Datamax Barcode Products Limited Warranty StatementThermal Printhead Warranty Service ProceduresLimitation of Liability General Warranty Provisions4203/E-4204/E-4304 Glossary 4203/E-4204/E-4304 4203/E-4204/E-4304 4203/E-4204/E-4304 4203/E-4204/E-4304 4203/E-4204/E-4304 Index Memory, 17, 24, 25, 27, 37, 38 Ribbon, 15, 16, 23, 44, 50, 52, 54, 55, 73, 76 4203/E-4204/E-4304