Datamax E-4204, E-4203, E-4304e manual New 19200 Baud Rate

Page 37

6.To confirm that your changes have been made press the + buttons simultaneously, this will print the Database Configuration Label. The label should show the new Baud Rate value of 19200.

FRI AUGUST 024, 2001 19:29 236 VER: E4204 - 04.06 08/24/01 BOOT 83-2329-04A

CODE 83-2325-04F

FONT 83-2337-01A

CPLD 592157-01C

INTERNAL FLASH MODULE PRESENT SYSTEM RAM CHECKS____ GOOD

SYSTEM RAM SIZE___ 2015 KBYTES SYSTEM RAM AVAIL__ 1244 KBYTES REG POWER SUPPLY__ YES

INPUT VALUES

PAPER_____________ 255

DARKNESS__________ 131

TRAN______________ 255

REFL______________ 149

RIBN______________ 87

TEMP______________ 48

VOLT______________ 223

CONFIGURATION

DIRECT THERMAL SERIAL PORT SELECTED 19.2; 8BITS

EDGE
CONT FORM LENGTH__			0
PRESENT ADJUST____			127
SOP ADJUST________			127
TOF LOW___________			0	0
TOF DELTA_________			10	10
TOF GAIN__________			12	10
OOS MAXVOLT_______			3	3
LABEL ALIGNMENT___			NO
ALIGN LENGTH______			100
STOP LOCATION_____		HOST
COUNTER INFORMATION
ABSOLUTE VALUES		6-18-2001
LENGTH____	773		INCHES
TIME______		20	HOURS
RESETTABLE VALUES		6-22-2001
LENGTH____	576		INCHES
TIME______		10	HOURS
MEMORY CONFIGURATION
INTERNAL MODULE______				15
SCALABLE FONTS_______				32
LABEL SIZE	0416:02157 IN

The new 19200 Baud Rate

E-4203/E-4204/E-4304

27

Image 37

Contents Operator’s Manual Page Copyright Information Agency Compliance and Approvals Important Safety Instructions Page Printer Overview Troubleshooting Appendix a Page Introduction About this Printer Standard FeaturesAdjustable Media Sensor Optional FeaturesPresent Sensor Removing the Packaging Before Using the PrinterAdditional Requirements Inspecting the PrinterPower Connection Connecting the PrinterInterface Cables Interface ConnectionAdjusting the Media Sensor Die-cut Near the center of the label Gap Page Loading Media 4203/E-4204/E-4304 Loading Media for Peel Configuration Loading Ribbon 4203/E-4204/E-4304 Flash Memory Expansion 4203/E-4204/E-4304 Lights Buttons Normal Mode Button FunctionsTo change Printer Setup Printer Setup Mode Button FunctionsValues Menu Numbers Items Printer Setup Menu ListMedia Type Sensor Type Menu Items and ValuesControl Codes Form Length Align Length Stop Location Step by Step Modification of the Printer Setup New 19200 Baud Rate Label Alignment = YES Label AlignmentLabel Alignment = no Label Alignment = AutoProblem Possible Cause Solution Label Alignment Troubleshooting~OR~ ~OR~ ~OR~ To perform Calibration Calibration Mode Button FunctionsAuto Media Sensor Calibration Manual Media Sensor Calibration Internal Labels Database Configuration and Dot Check LabelsGood Dot Check Label Hex Dump Label Test LabelTo exit the Hex Dump Mode Area Method Interval Cleaning the Printhead Media Width Adjustment Ribbon Width Adjustment Fine Printhead Adjustment Removal Printhead ReplacementResetting to the Factory Defaults Darkness AdjustmentDownloading Firmware and Fonts Paused Light will flash during the download Problem Situation Troubleshooting TipsUnacceptable print quality Skips every other label Label advances 1-2 inches before a fault indication Printing MechanicalCommunications Media/RibbonFonts Embedded Bar CodesDesignator Description Maximum1 Minimum1 Approved Media4203/E-4204/E-4304 Ascii Control Code Chart XON Font Valid Ascii Characters decimal Use with Record Embedded Fonts and BarcodesAlphanumeric, upper and lower Font 6 62-character alphanumeric, uppercase 4203/E-4204/E-4304 Bar Code Type Length Check Valid Ascii Characters Sum BarcodesFIM Barcode a Code 3 Barcode I Codabar Kmart NON EDI Barcode T Telepen Printer Datamax Barcode Products Limited Warranty StatementThermal Printhead Warranty Service ProceduresLimitation of Liability General Warranty Provisions4203/E-4204/E-4304 Glossary 4203/E-4204/E-4304 4203/E-4204/E-4304 4203/E-4204/E-4304 4203/E-4204/E-4304 4203/E-4204/E-4304 Index Memory, 17, 24, 25, 27, 37, 38 Ribbon, 15, 16, 23, 44, 50, 52, 54, 55, 73, 76 4203/E-4204/E-4304