Datamax E-4304e, E-4203, E-4204 manual Glossary

Page 83

Glossary

alphanumeric Consisting of alphabetic, numeric, punctuation and other symbols.

backing material The silicon-coated paper carrier material to which labels with adhesive backing are affixed. Also referred to as “liner”.

bar code A representation of alphanumeric information in a pattern of machine-readable marks. The basic categories are divided into one-dimensional (UPC, Code 39, Postnet, etc.) and two-dimensional barcodes (DataMatrix, MaxiCode, PDF417, etc.).

burn line The row of thermal elements in the printhead that create the images on the media.

calibration The process through which sensor readings are entered into the printer for correct sensor function (for example, detection of a given media type) and TOF positioning.

character set The entire complement of alphanumeric symbols contained in a given font.

checksum An alphanumeric error detection method used in many bar code symbologies for informational security.

continuous media An uninterrupted roll or box of label or tag media that contains no gap, notch, or mark to separate individual labels or tags.

core diameter The inside diameter measurement of the cardboard core at the center of a ribbon or media roll.

E-4203/E-4204/E-4304

73

Image 83
Contents Operator’s Manual Page Copyright Information Agency Compliance and Approvals Important Safety Instructions Page Printer Overview Troubleshooting Appendix a Page Introduction About this Printer Standard FeaturesAdjustable Media Sensor Optional FeaturesPresent Sensor Removing the Packaging Before Using the PrinterAdditional Requirements Inspecting the PrinterPower Connection Connecting the PrinterInterface Cables Interface ConnectionAdjusting the Media Sensor Die-cut Near the center of the label Gap Page Loading Media 4203/E-4204/E-4304 Loading Media for Peel Configuration Loading Ribbon 4203/E-4204/E-4304 Flash Memory Expansion 4203/E-4204/E-4304 Lights Buttons Normal Mode Button FunctionsTo change Printer Setup Printer Setup Mode Button FunctionsValues Menu Numbers Items Printer Setup Menu ListMedia Type Sensor Type Menu Items and ValuesControl Codes Form Length Align Length Stop Location Step by Step Modification of the Printer Setup New 19200 Baud Rate Label Alignment = YES Label AlignmentLabel Alignment = no Label Alignment = AutoProblem Possible Cause Solution Label Alignment Troubleshooting~OR~ ~OR~ ~OR~ To perform Calibration Calibration Mode Button FunctionsAuto Media Sensor Calibration Manual Media Sensor Calibration Internal Labels Database Configuration and Dot Check LabelsGood Dot Check Label Hex Dump Label Test LabelTo exit the Hex Dump Mode Area Method Interval Cleaning the Printhead Media Width Adjustment Ribbon Width Adjustment Fine Printhead Adjustment Removal Printhead ReplacementDownloading Firmware and Fonts Darkness AdjustmentResetting to the Factory Defaults Paused Light will flash during the download Problem Situation Troubleshooting TipsUnacceptable print quality Skips every other label Label advances 1-2 inches before a fault indication Printing MechanicalEmbedded Bar Codes Media/RibbonCommunications FontsDesignator Description Maximum1 Minimum1 Approved Media4203/E-4204/E-4304 Ascii Control Code Chart XON Font Valid Ascii Characters decimal Use with Record Embedded Fonts and BarcodesAlphanumeric, upper and lower Font 6 62-character alphanumeric, uppercase 4203/E-4204/E-4304 Bar Code Type Length Check Valid Ascii Characters Sum BarcodesFIM Barcode a Code 3 Barcode I Codabar Kmart NON EDI Barcode T Telepen Printer Datamax Barcode Products Limited Warranty StatementThermal Printhead Warranty Service ProceduresLimitation of Liability General Warranty Provisions4203/E-4204/E-4304 Glossary 4203/E-4204/E-4304 4203/E-4204/E-4304 4203/E-4204/E-4304 4203/E-4204/E-4304 4203/E-4204/E-4304 Index Memory, 17, 24, 25, 27, 37, 38 Ribbon, 15, 16, 23, 44, 50, 52, 54, 55, 73, 76 4203/E-4204/E-4304