Datamax E-4203, E-4204, E-4304e manual ~Or~

Page 42

Problem	Possible Cause		Solution
Label Alignment is	Label Alignment	¾	Set Label Alignment to
incorrect. Pressing	Length is not		AUTO. Press and hold FEED
FEED successively	correct. The		until paper moves for
results in a short	default Label		automatic Label Alignment
label length, one-	Alignment Length is		Length measurement.
inch.	1.00”, and will		~OR~
	result in this		~OR~
	result in this		Measure the label length and
	behavior when any	¾	Measure the label length and
	larger label length		use the Setup Menu to set the
	is used without		new length. Print a Database
	setting the		Configuration label to ensure
	appropriate length.		the new length has been set.

Label Alignment is	Label Alignment	¾	Set Label Alignment to
incorrect. Pressing	Length is not		AUTO. Press and hold FEED
FEED successively	correct. The		until paper moves for
results in a label	default Label		automatic Label Alignment
length longer than	Alignment Length is		length measurement.
actual, one-inch.	1.00”, and will		~OR~
	result in this		~OR~
	result in this
	behavior when any	¾	Measure the label length and
	larger label length		use the Setup Menu to set the
	is used without		new length. Print a Database
	setting the		Configuration label to ensure
	appropriate length		the new length has been set.

32	E-4203/E-4204/E-4304

Image 42

Contents Operator’s Manual Page Copyright Information Agency Compliance and Approvals Important Safety Instructions Page Printer Overview Troubleshooting Appendix a Page Introduction Standard Features About this PrinterOptional Features Adjustable Media SensorPresent Sensor Before Using the Printer Removing the PackagingInspecting the Printer Additional RequirementsConnecting the Printer Power ConnectionInterface Connection Interface CablesAdjusting the Media Sensor Die-cut Near the center of the label Gap Page Loading Media 4203/E-4204/E-4304 Loading Media for Peel Configuration Loading Ribbon 4203/E-4204/E-4304 Flash Memory Expansion 4203/E-4204/E-4304 Lights Normal Mode Button Functions ButtonsPrinter Setup Mode Button Functions To change Printer SetupPrinter Setup Menu List Values Menu Numbers ItemsMenu Items and Values Media Type Sensor TypeControl Codes Form Length Align Length Stop Location Step by Step Modification of the Printer Setup New 19200 Baud Rate Label Alignment Label Alignment = YESLabel Alignment = Auto Label Alignment = noLabel Alignment Troubleshooting Problem Possible Cause Solution~OR~ ~OR~ ~OR~ Calibration Mode Button Functions To perform CalibrationAuto Media Sensor Calibration Manual Media Sensor Calibration Database Configuration and Dot Check Labels Internal LabelsGood Dot Check Label Test Label Hex Dump LabelTo exit the Hex Dump Mode Area Method Interval Cleaning the Printhead Media Width Adjustment Ribbon Width Adjustment Fine Printhead Adjustment Printhead Replacement RemovalDarkness Adjustment Resetting to the Factory DefaultsDownloading Firmware and Fonts Paused Light will flash during the download Troubleshooting Tips Problem SituationUnacceptable print quality Skips every other label Label advances 1-2 inches before a fault indication Mechanical PrintingFonts Media/RibbonCommunications Embedded Bar CodesApproved Media Designator Description Maximum1 Minimum14203/E-4204/E-4304 Ascii Control Code Chart XON Embedded Fonts and Barcodes Font Valid Ascii Characters decimal Use with RecordAlphanumeric, upper and lower Font 6 62-character alphanumeric, uppercase 4203/E-4204/E-4304 Barcodes Bar Code Type Length Check Valid Ascii Characters SumFIM Barcode a Code 3 Barcode I Codabar Kmart NON EDI Barcode T Telepen Datamax Barcode Products Limited Warranty Statement PrinterWarranty Service Procedures Thermal PrintheadGeneral Warranty Provisions Limitation of Liability4203/E-4204/E-4304 Glossary 4203/E-4204/E-4304 4203/E-4204/E-4304 4203/E-4204/E-4304 4203/E-4204/E-4304 4203/E-4204/E-4304 Index Memory, 17, 24, 25, 27, 37, 38 Ribbon, 15, 16, 23, 44, 50, 52, 54, 55, 73, 76 4203/E-4204/E-4304