Datamax E-4203, E-4204, E-4304e manual Area Method Interval

Page 51

5.0 Introduction

This chapter details the cleaning, adjusting, and troubleshooting tips for the printer. The following table outlines the recommended maintenance schedule for the various printer parts.

Area	Method	Interval
Printhead	Turn off the printer before cleaning	After every roll
	the printhead. Use solvent* on a	of media.
	cotton swab to clean the printhead
	from end to end.
Platen Roller	Turn the power off. Rotate the	After every roll
	platen roller and clean it thoroughly	of media.
	with solvent* and a cotton swab.
Peel-Off	Rotate the peel-off roller and clean	After every roll
Roller	it thoroughly with solvent* and a	of media.
	cotton swab.
Media Path	Solvent*	After every roll
		of media.
Peel/Tear Bar	Solvent*	As needed
Media Sensor	Air blow	Monthly
Exterior	Mild detergent or desktop cleaner.	As needed
Interior	Brush or vacuum cleaner	As needed.

* It is recommended that a solvent containing isopropyl alcohol be used.

Isopropyl alcohol is a flammable solvent, always take the proper Warning precautions when using this substance.

E-4203/E-4204/E-4304

41

Image 51

Contents Operator’s Manual Page Copyright Information Agency Compliance and Approvals Important Safety Instructions Page Printer Overview Troubleshooting Appendix a Page Introduction About this Printer Standard FeaturesAdjustable Media Sensor Optional FeaturesPresent Sensor Removing the Packaging Before Using the PrinterAdditional Requirements Inspecting the PrinterPower Connection Connecting the PrinterInterface Cables Interface ConnectionAdjusting the Media Sensor Die-cut Near the center of the label Gap Page Loading Media 4203/E-4204/E-4304 Loading Media for Peel Configuration Loading Ribbon 4203/E-4204/E-4304 Flash Memory Expansion 4203/E-4204/E-4304 Lights Buttons Normal Mode Button FunctionsTo change Printer Setup Printer Setup Mode Button FunctionsValues Menu Numbers Items Printer Setup Menu ListMedia Type Sensor Type Menu Items and ValuesControl Codes Form Length Align Length Stop Location Step by Step Modification of the Printer Setup New 19200 Baud Rate Label Alignment = YES Label AlignmentLabel Alignment = no Label Alignment = AutoProblem Possible Cause Solution Label Alignment Troubleshooting~OR~ ~OR~ ~OR~ To perform Calibration Calibration Mode Button FunctionsAuto Media Sensor Calibration Manual Media Sensor Calibration Internal Labels Database Configuration and Dot Check LabelsGood Dot Check Label Hex Dump Label Test LabelTo exit the Hex Dump Mode Area Method Interval Cleaning the Printhead Media Width Adjustment Ribbon Width Adjustment Fine Printhead Adjustment Removal Printhead ReplacementDarkness Adjustment Resetting to the Factory DefaultsDownloading Firmware and Fonts Paused Light will flash during the download Problem Situation Troubleshooting TipsUnacceptable print quality Skips every other label Label advances 1-2 inches before a fault indication Printing MechanicalEmbedded Bar Codes Media/RibbonCommunications FontsDesignator Description Maximum1 Minimum1 Approved Media4203/E-4204/E-4304 Ascii Control Code Chart XON Font Valid Ascii Characters decimal Use with Record Embedded Fonts and BarcodesAlphanumeric, upper and lower Font 6 62-character alphanumeric, uppercase 4203/E-4204/E-4304 Bar Code Type Length Check Valid Ascii Characters Sum BarcodesFIM Barcode a Code 3 Barcode I Codabar Kmart NON EDI Barcode T Telepen Printer Datamax Barcode Products Limited Warranty StatementThermal Printhead Warranty Service ProceduresLimitation of Liability General Warranty Provisions4203/E-4204/E-4304 Glossary 4203/E-4204/E-4304 4203/E-4204/E-4304 4203/E-4204/E-4304 4203/E-4204/E-4304 4203/E-4204/E-4304 Index Memory, 17, 24, 25, 27, 37, 38 Ribbon, 15, 16, 23, 44, 50, 52, 54, 55, 73, 76 4203/E-4204/E-4304