Datamax E-4304e, E-4203, E-4204 manual Fim

Page 74

Bar Code	Type	Length	Check-	Valid ASCII Characters,
ID			sum	decimal value
				representation
u	UPS MaxiCode with	Specified	Yes	Alphanumeric
	Byte Count
v	FIM	1	No	A, B, C, D
z	PDF417	Varies	Yes	All
Z	PDF417 with Byte	Specified	Yes	All
	Count
W1c	DataMatrix	Varies	Yes	All 8-bit values
W1C	DataMatrix with Byte	Specified	Yes	All 8-bit values
	Count
W1d	QR Code – Auto	Varies	Yes	Alphanumeric
	format
W1D	QR Code – Manual	Varies	Yes	Single-byte or Kanji double-
	format			byte
W1f	Aztec	Varies	Yes	All 8-bit values
W1F	Aztec with Byte	Specified	Yes	All 8-bit values
	Count
W1T	TCIF Linked	Varies	No	Alphanumeric
	Barcode 3 of 9
	(TLC39)
W1z	MicroPDF417	Varies	Yes	All 8-bit values
W1Z	MicroPDF417 with	Specified	Yes	All 8-bit values
	Byte Count

64	E-4203/E-4204/E-4304

Image 74

Contents Operator’s Manual Page Copyright Information Agency Compliance and Approvals Important Safety Instructions Page Printer Overview Troubleshooting Appendix a Page Introduction Standard Features About this PrinterOptional Features Adjustable Media SensorPresent Sensor Before Using the Printer Removing the PackagingInspecting the Printer Additional RequirementsConnecting the Printer Power ConnectionInterface Connection Interface CablesAdjusting the Media Sensor Die-cut Near the center of the label Gap Page Loading Media 4203/E-4204/E-4304 Loading Media for Peel Configuration Loading Ribbon 4203/E-4204/E-4304 Flash Memory Expansion 4203/E-4204/E-4304 Lights Normal Mode Button Functions ButtonsPrinter Setup Mode Button Functions To change Printer SetupPrinter Setup Menu List Values Menu Numbers ItemsMenu Items and Values Media Type Sensor TypeControl Codes Form Length Align Length Stop Location Step by Step Modification of the Printer Setup New 19200 Baud Rate Label Alignment Label Alignment = YESLabel Alignment = Auto Label Alignment = noLabel Alignment Troubleshooting Problem Possible Cause Solution~OR~ ~OR~ ~OR~ Calibration Mode Button Functions To perform CalibrationAuto Media Sensor Calibration Manual Media Sensor Calibration Database Configuration and Dot Check Labels Internal LabelsGood Dot Check Label Test Label Hex Dump LabelTo exit the Hex Dump Mode Area Method Interval Cleaning the Printhead Media Width Adjustment Ribbon Width Adjustment Fine Printhead Adjustment Printhead Replacement RemovalDownloading Firmware and Fonts Darkness AdjustmentResetting to the Factory Defaults Paused Light will flash during the download Troubleshooting Tips Problem SituationUnacceptable print quality Skips every other label Label advances 1-2 inches before a fault indication Mechanical PrintingFonts Media/RibbonCommunications Embedded Bar CodesApproved Media Designator Description Maximum1 Minimum14203/E-4204/E-4304 Ascii Control Code Chart XON Embedded Fonts and Barcodes Font Valid Ascii Characters decimal Use with RecordAlphanumeric, upper and lower Font 6 62-character alphanumeric, uppercase 4203/E-4204/E-4304 Barcodes Bar Code Type Length Check Valid Ascii Characters SumFIM Barcode a Code 3 Barcode I Codabar Kmart NON EDI Barcode T Telepen Datamax Barcode Products Limited Warranty Statement PrinterWarranty Service Procedures Thermal PrintheadGeneral Warranty Provisions Limitation of Liability4203/E-4204/E-4304 Glossary 4203/E-4204/E-4304 4203/E-4204/E-4304 4203/E-4204/E-4304 4203/E-4204/E-4304 4203/E-4204/E-4304 Index Memory, 17, 24, 25, 27, 37, 38 Ribbon, 15, 16, 23, 44, 50, 52, 54, 55, 73, 76 4203/E-4204/E-4304