ATI Technologies X1650 manual Screen Defects

Page 46

110 Troubleshooting

General Troubleshooting

Problem

Possible Solution

 

 

No Display

• Check that the card is seated properly in its expansion

 

slot.

 

• Ensure that the monitor cable is securely fastened to

 

the card.

 

• Make sure that the monitor and computer are plugged

 

in and receiving power.

 

• If necessary, disable any built-in graphics capabilities

 

on your mother board. For more information, consult

 

your computer’s manual or manufacturer. (Note: some

 

manufacturers do not allow the built-in graphics to be

 

disabled or to become the secondary display.)

 

• Make sure that you selected the appropriate monitor

 

when you installed your enhanced driver.

 

 

Screen Defects

• Check if your monitor supports the resolution,

Appear

horizontal (kHz) and vertical (Hz) refresh rates as

 

required by the graphics card.

 

• Check your current resolution, refresh rate, and color

 

depth settings in the Settings and Monitor tabs in your

 

Display Properties dialog.

 

Warning! Ensure that both video card and monitor

 

support resolution and refresh rates you select.

 

Incompatible resolution/refresh rate selection may result in

 

monitor damage. Refer to your monitor's documentation

 

for recommended resolutions and refresh rates.

 

 

Off-Center

• Try adjusting the brightness, sharpness, contrast, and

Screen Image,

color balance controls of your monitor.

Odd Colors or No

• Try adjusting the centering and positioning controls of

Picture

your monitor to position the picture on the screen

 

• Set the monitor's RGB inputs (and sync switches, if this

 

option is available) to 75 Ohms, with the sync set to

 

external.

 

• Digital Flat Panel (DFP) monitor users: refer to your

 

monitor's documentation for the appropriate cable and

 

connector to plug into the DVI-I connector on the

 

graphics card.

 

 

Operating

• Check the driver installation and make sure that all

System Warns

software is correctly loaded corresponding to your

that Video Card

operating system and applications.

Isn’t Properly

Re-install the ATI drivers for your Radeon® X1650 PRO

Configured

card.

 

 

Image 46
Contents Radeon X1650 PRO Page Iii Disclaimer Important Safety Instructions Page Table of Contents Glossary Index Introduction Radeon X1650 PRO FeaturesFeatures Ring Bus Memory ControllerAdvanced Image Quality Features Avivo Video and Display PlatformCrossFire Uninstall Previous Graphics Card Drivers System RequirementsTo uninstall previous drivers System Requirements Using Multiple Displays Connecting Your MonitorsTo connect your monitors Display Configurations Display Connectors Comments Configuration UsedDisplay Configurations Using TV Out Using TV Display and Capture FeaturesViewing Your PC Display on a TV Connecting to a TV or VCR To connect S-Video OutUsing a Monitor vs. Using TV Display Connecting Your S-Video Out to a TV or VCRUsing Games and Applications Connecting to HdtvUsing a TV as the Only Display Viewing Text on a TVInstalling your ATI Hdtv video cable ATI Hdtv CableUsing Your ATI Hdtv Video Cable Software Installation Prerequisites Installing Software and DriversInstalling Drivers and Software in Windows To install ATI drivers and softwareMonitor Configuration Reinstalling Drivers To set up a multi-monitor displayTo configure your primary display To manually reinstall drivers Express or Custom Install Installing the Catalyst Software Suite Catalyst Control Center Launching Catalyst Control CenterLaunching Catalyst Control Center Using the System Tray Launching Catalyst Control Center Using the Start MenuOther Quick Launch Access Points Launching Catalyst Control Center Using Hot KeysCrossFire FAQ What graphics cards work with CrossFire?Page Is a driver profile required to make CrossFire work? On what basis are different rendering modes chosen? CrossFire Overview Welcome to CrossFireAllowable CrossFire System Components CrossFire Rendering Modes SuperTiling Scissor Mode Alternate Frame Rendering AFR Mode Super Anti-aliasing Mode CrossFire Overview CrossFire Overview Troubleshooting ReferenceScreen Defects CrossFire -Specific Troubleshooting CrossFire-Specific Troubleshooting Problem Possible Solution Compliance Information Additional AccessoriesFCC Compliance Information CE Compliance Information Electrical SafetyIndustry Canada Compliance Statement Informations de conformité de la CEThis product was manufactured by ATI Technologies Inc Glossary 3DcAlpha Blending Adaptive Anti-aliasingAGP Alternate Frame RenderingAspect Anisotropic FilteringAnti-aliasing Aspect RatioBit Depth Back BufferBilinear Filtering BitmapColor Component BufferCatalyst Control Center Color CorrectionCompositing Engine Component VideoComposite Video Control PointCRT Flat Shading DVIEdtv FogGouraud Shading Frames Per SecondGamma HdcpHydraVision HdtvHue HyperZ HDLighting Keyframe InterpolationKTX Buffer Region Extension MipmappingPAL NtscPCI Pixel PCI Express PCIePipeline PulldownRendering ResolutionRefresh Rate SaturationSecam Scissor ModeSdtv Shadow MaskSpecular Highlight SmartShader HDSmoothVision HD Super Anti-aliasingTexel SuperTilingVideo Texture MappingVector Adaptive Deinterlacing Transition Minimized Differential Signaling TmdsTrilinear Filtering VersaVisionVideo Immersion VGA ConnectorVertex shader units VideoShader HDVPU Recover YPbPr