American Dryer Corp Phase 7.2.2 user manual Section Phase 7 NON-COIN Auto Cycle Patent no ,827,627

Page 4

SECTION IV
OPERATING INSTRUCTIONS		14
A.	Operating Sequence	14
B.	Operating Notes	18
C. Fire Suppression System (F.S.S.) Theory Of Operation		19
SECTION V
L.E.D. DISPLAY MESSAGES		22
A. L.E.D. Display Operating Status		22
SECTION VI
PROGRAMMING INSTRUCTIONS		23
A.	Introduction to Programming	23
B. Programming Flowcharts		25
SECTION VII
FACTORY PRESET PARAMETERS (PROGRAMS)		75
A. Cycle “A-F” Parameters (Programs) Preset by the Factory		75
B. Cycle “0-40” Parameters (Programs) Preset by the Factory		75
SECTION VIII
PHASE 7 NON-COIN MICROPROCESSOR CONTROLLER (COMPUTER)
PROGRAMMING LIMITS		76
A. Preprogrammed Cycles		76
B. System Parameters (Program Locations)		77
C.	Fixed Parameters	77
SECTION IX
PHASE 7 NON-COIN AUTO CYCLE (PATENT NO. 4,827,627)
CYCLE ADJUSTMENT VALUES		78
SECTION X
PHASE 7 NON-COIN MICROPROCESSOR CONTROLLER (COMPUTER)
SYSTEM DIAGNOSTICS		79
A. Diagnostic (L.E.D. Display) Fault Messages		79
B.	F.S.S. Diagnostic Conditions	83
C. Input/Output (I/O) Board L.E.D. Indicators		84
D. Keyboard (Touch Pad) Layout		85

SECTION XI
CUSTOMER CUSTOM PARAMETER SETTINGS	86

Image 4

Contents NON-COIN Retain This Manual In a Safe Place For Future Reference Table of Contents Section Phase 7 NON-COIN Auto Cycle Patent no ,827,627 Section Features Keyboard Touch Pad Symbols = STOP/CLEAR key Program Selections Preprogrammed CyclesPage Automatic Drying Cycle Patent no ,827,627 Operations Manually Loaded CyclesTimed Manual Drying Cycle Operation Temperature Conversion Status Cycle in Progress Temperature DisplayLight Emitting Diode L.E.D. DOT Matrix Display Audio Alert on Times 0 to Wrinkle Guard ProgramPreprogrammed Cycle Preview Reversing Option DiagnosticsProgram Locations Page Preprogrammed Locations for Custom Drying Operating Instructions Operating SequencePage Page MAN Operating Notes System Reset Fire Suppression System F.S.S. Theory of OperationFire Suppression System F.S.S. Valve Check Page D. Display Messages E.D. Display Operating StatusProgramming Instructions Introduction to ProgrammingPage Programming Flowcharts START/ENTER STOP/CLEARPhase Menu Programming Procedure Page Auto Reverse Mode On OFF Selecting Languages 0SELECT LanguageEnglish EspanolDryer Setup Selecting a Dryer ModelSelect System Parameters Select ModelGAS Reversing GAS REVERSING, Electric REVERSING, Steam REVERSING, GAS NONSteam NON-REVERSING Electric ReversingSelecting the System Temperature DEG F Enter Lint Cleaning Frequency 1 to 10 HoursDEG C Setting the Lint Cleaning Frequency Enter Audio Alert on Times 0 to Adjusting the Audio Alert On times System Temp Rotation Sensor Rotation Sensor Press Enter to jump directly to the location OFF Board Address 00 to ZZDryer Address To ZZ Auto Cycle Time OUT to 99 Minutes Auto Cycle Time Out System Temp Enter Lint Cleaning Frequency 1 to 10 Hours Enter Audio Alert on Times 0 to Rotation SensorAuto Cycle Time OUT To 99 Minutes Adjusting Reversing Spin Time and Stop Time Enter Spin Time 30 to 120 Seconds Reversing SetupEnter Stop Time 5 to 10 Seconds Press the up arrow key to increment Setup Wrinkle Guard Audio AlertWrinkle Guard Setup Wrinkle Guard Audio AlertSteam Injection Setup Wrinkle Guard Setup Steam Injection Setup Enter 1ST on Time Cycle511 to 000 First time adjustment is Minutes mm Enter 1ST OFF TimeEnter 2ND on Time Enter 3RD on Time Program 0-40 CyclesProgramming a F Cycles or 0 40 Cycles Program System Cycles ParametersReverse Mode Select a F KEYSelect Cycle Type AutoNot Available Enter DRY TempOFF Not Available TimeDRY Enter Dryness LevelEnter Stop Time To 10 Seconds DRY or Extra Extra DRY Enter Cycle AdjustmentEnter DRY Time 0 to 99 Minutes Controlled Cool Down Enter Cool Down Time 0 to 99 MinutesEnter Cool Down Temp 70 to 100 ºF Enter Cool DownSteam Injection Cycle Enter 1ST on Time 511 to From Previous Enter 2ND on Time Enter 3RD on Time Restoring Factory Default Settings Enter Password Confirm Defaults Defaults SET Default Settings YESCycle A-F Parameters Programs Preset by the Factory Cycle 0-40 Parameters Programs Preset by the FactoryPreprogrammed Cycles System Parameters Program Locations Fixed ParametersGas Diagnostic L.E.D. Display Fault Messages StandardsPage Page Page S.S. Diagnostic Conditions INPUT/OUTPUT I/O Board L.E.D. Indicators Brhl RED L.E.DKeyboard Touch PAD Layout Customer Custom Parameter Settings Auto Programmed Cycle Page ADC Part No 08/19/08