American Dryer Corp Phase 7.2.2 user manual Enter 2ND on Time

Page 72

From

Previous

ENTER 2ND ON TIME

8:21 TO 45:00

0:00

9

9

The first time adjustment is Minutes mm:

Press the up arrow key to increment the time in minutes, the down arrow key to decrement the time in minutes or enter the time in minutes directly.

Press ENTER to store

new changes

9:00

4

0

40

The second time adjustment is

Seconds :ss

Press the up arrow key to increment the time in seconds, the down arrow key to decrement the time in seconds or enter the time in seconds directly.

Next page

70

Image 72

Contents NON-COIN Retain This Manual In a Safe Place For Future Reference Table of Contents Section Phase 7 NON-COIN Auto Cycle Patent no ,827,627 Section Features Keyboard Touch Pad Symbols = STOP/CLEAR key Program Selections Preprogrammed CyclesPage Manually Loaded Cycles Automatic Drying Cycle Patent no ,827,627 OperationsTimed Manual Drying Cycle Operation Cycle in Progress Temperature Display Temperature Conversion StatusLight Emitting Diode L.E.D. DOT Matrix Display Wrinkle Guard Program Audio Alert on Times 0 toPreprogrammed Cycle Preview Diagnostics Reversing OptionProgram Locations Page Preprogrammed Locations for Custom Drying Operating Instructions Operating SequencePage Page MAN Operating Notes System Reset Fire Suppression System F.S.S. Theory of OperationFire Suppression System F.S.S. Valve Check Page D. Display Messages E.D. Display Operating StatusProgramming Instructions Introduction to ProgrammingPage Programming Flowcharts START/ENTER STOP/CLEARPhase Menu Programming Procedure Page Auto Reverse Mode On OFF Selecting Languages 0SELECT LanguageEnglish EspanolDryer Setup Selecting a Dryer ModelSelect System Parameters Select ModelGAS Reversing GAS REVERSING, Electric REVERSING, Steam REVERSING, GAS NONSteam NON-REVERSING Electric ReversingSelecting the System Temperature Enter Lint Cleaning Frequency 1 to 10 Hours DEG FDEG C Setting the Lint Cleaning Frequency Enter Audio Alert on Times 0 to Adjusting the Audio Alert On times System Temp Rotation Sensor Rotation Sensor Press Enter to jump directly to the location OFF Board Address 00 to ZZDryer Address To ZZ Auto Cycle Time OUT to 99 Minutes Auto Cycle Time Out System Temp Enter Lint Cleaning Frequency 1 to 10 Hours Enter Audio Alert on Times 0 to Rotation SensorAuto Cycle Time OUT To 99 Minutes Adjusting Reversing Spin Time and Stop Time Reversing Setup Enter Spin Time 30 to 120 SecondsEnter Stop Time 5 to 10 Seconds Press the up arrow key to increment Setup Wrinkle Guard Audio AlertWrinkle Guard Setup Wrinkle Guard Audio AlertSteam Injection Setup Wrinkle Guard Setup Steam Injection Setup Enter 1ST on Time Cycle511 to 000 First time adjustment is Minutes mm Enter 1ST OFF TimeEnter 2ND on Time Enter 3RD on Time Program 0-40 CyclesProgramming a F Cycles or 0 40 Cycles Program System Cycles ParametersReverse Mode Select a F KEYSelect Cycle Type AutoNot Available Enter DRY TempOFF Not Available TimeEnter Dryness Level DRYEnter Stop Time To 10 Seconds Enter Cycle Adjustment DRY or Extra Extra DRYEnter DRY Time 0 to 99 Minutes Controlled Cool Down Enter Cool Down Time 0 to 99 MinutesEnter Cool Down Temp 70 to 100 ºF Enter Cool DownSteam Injection Cycle Enter 1ST on Time 511 to From Previous Enter 2ND on Time Enter 3RD on Time Restoring Factory Default Settings Enter Password Confirm Defaults Defaults SET Default Settings YESCycle A-F Parameters Programs Preset by the Factory Cycle 0-40 Parameters Programs Preset by the FactoryPreprogrammed Cycles System Parameters Program Locations Fixed ParametersGas Diagnostic L.E.D. Display Fault Messages StandardsPage Page Page S.S. Diagnostic Conditions INPUT/OUTPUT I/O Board L.E.D. Indicators Brhl RED L.E.DKeyboard Touch PAD Layout Customer Custom Parameter Settings Auto Programmed Cycle Page ADC Part No 08/19/08