American Dryer Corp Phase 7.2.2 INPUT/OUTPUT I/O Board L.E.D. Indicators, Brhl RED L.E.D

Page 86

C.INPUT/OUTPUT (I/O) BOARD L.E.D. INDICATORS

1.Inputs

1. ESTOP – (RED L.E.D.) This light emitting diode (L.E.D.) will indicate the status of the E-STOP. If the E-

STOP has been pressed, then the L.E.D. is ON.

2.GAS_V – (RED L.E.D.) This L.E.D. will indicate the status of the gas valve. If the gas valve is open (ON), then the L.E.D. is ON.

3.

BRHL – (RED L.E.D.)

This L.E.D. will indicate the status of the burner high limit disk. If the disk is

 

 

closed (temperature below 330° F [166° C]), then the L.E.D. is ON.

4.

SAIL – (RED L.E.D.)

This L.E.D. will indicate the status of the sail switch. If the switch is closed, then

 

 

the L.E.D. is ON.

5.

EXHL – (RED L.E.D.)

This L.E.D. will indicate the status of the exhaust high limit disk. If the disk is

 

 

closed (temperature below 225° F [107° C]), then the L.E.D. is ON.

6.

MAIN – (RED L.E.D.)

This L.E.D. will indicate the status of the main door. If the door is closed, then

 

 

the L.E.D. is ON.

7.

LINT – (RED L.E.D.)

This L.E.D. will indicate the status of the lint drawer. If the drawer is closed,

 

 

then the L.E.D. is ON.

8.

FUSE – (RED L.E.D.)

This L.E.D. will indicate the status of the Phase 7 non-coin microprocessor

 

 

controller (computer) voltage. If the POWER ON button is pressed (green button

 

 

light is on), then the L.E.D. is ON.

9.

H2O – (RED L.E.D.)

This L.E.D. will indicate the status of the water pressure switch on the Fire

 

 

Suppression System (F.S.S.) water line. If water pressure is present, then the

L.E.D. is ON.

2.Outputs

10.

F.S.S. – (GREEN L.E.D.)

This L.E.D. will indicate that the F.S.S. system output is activated.

11.

STEAM – (GREEN L.E.D.)

This L.E.D. will indicate the status of the steam injection output. If the

 

 

request to turn on the steam injection is made, then the L.E.D. is ON.

12.

_HEAT – (GREEN L.E.D.)

This L.E.D. will indicate the status of the heat output. If the request to turn

 

 

on the heater is made, then the L.E.D. is ON.

13.

AIR – (GREEN L.E.D.)

This L.E.D. will indicate the status of the air jet output. If the request to

 

 

turn on the air jet is made, then the L.E.D. is ON.

14.

REV – (GREEN L.E.D.)

This L.E.D. will indicate the status of the basket (tumbler) reverse direction

 

 

output. If the request to tumble the drum in the reverse direction is made,

 

 

then the L.E.D. is ON.

15.

FWD – (GREEN L.E.D.)

This L.E.D. will indicate the status of the basket (tumbler) forward direction

 

 

output. If the request to tumble the drum in the forward direction is made,

 

 

then the L.E.D. is ON.

16.

FAN – (GREEN L.E.D.)

This L.E.D. will indicate the status of the fan output. If the request to turn

 

 

on the fan (blower) is made, then the L.E.D. is ON.

84

Page 85 Page 87
Image 86
Page 85 Page 87
Contents NON-COIN Retain This Manual In a Safe Place For Future Reference Table of Contents Section Phase 7 NON-COIN Auto Cycle Patent no ,827,627 Section Features Keyboard Touch Pad Symbols = STOP/CLEAR key Program Selections Preprogrammed CyclesPage Timed Manual Drying Cycle Operation Manually Loaded CyclesAutomatic Drying Cycle Patent no ,827,627 Operations Light Emitting Diode L.E.D. DOT Matrix Display Cycle in Progress Temperature DisplayTemperature Conversion Status Preprogrammed Cycle Preview Wrinkle Guard ProgramAudio Alert on Times 0 to Program Locations DiagnosticsReversing Option Page Preprogrammed Locations for Custom Drying Operating Instructions Operating SequencePage Page MAN Operating Notes System Reset Fire Suppression System F.S.S. Theory of OperationFire Suppression System F.S.S. Valve Check Page D. Display Messages E.D. Display Operating StatusProgramming Instructions Introduction to ProgrammingPage Programming Flowcharts START/ENTER STOP/CLEARPhase Menu Programming Procedure Page Auto Reverse Mode On OFF English Selecting Languages0SELECT Language EspanolSelect System Parameters Dryer SetupSelecting a Dryer Model Select ModelSteam NON-REVERSING GAS ReversingGAS REVERSING, Electric REVERSING, Steam REVERSING, GAS NON Electric ReversingSelecting the System Temperature DEG C Enter Lint Cleaning Frequency 1 to 10 HoursDEG F Setting the Lint Cleaning Frequency Enter Audio Alert on Times 0 to Adjusting the Audio Alert On times System Temp Rotation Sensor Rotation Sensor Press Enter to jump directly to the location OFF Board Address 00 to ZZDryer Address To ZZ Auto Cycle Time OUT to 99 Minutes Auto Cycle Time Out System Temp Enter Lint Cleaning Frequency 1 to 10 Hours Enter Audio Alert on Times 0 to Rotation SensorAuto Cycle Time OUT To 99 Minutes Adjusting Reversing Spin Time and Stop Time Enter Stop Time 5 to 10 Seconds Reversing SetupEnter Spin Time 30 to 120 Seconds Press the up arrow key to increment Setup Wrinkle Guard Audio AlertWrinkle Guard Setup Wrinkle Guard Audio AlertSteam Injection Setup Wrinkle Guard Setup Steam Injection Setup Enter 1ST on Time Cycle511 to 000 First time adjustment is Minutes mm Enter 1ST OFF TimeEnter 2ND on Time Enter 3RD on Time Program 0-40 CyclesProgramming a F Cycles or 0 40 Cycles Program System Cycles ParametersSelect Cycle Type Reverse ModeSelect a F KEY AutoOFF Not Available Not AvailableEnter DRY Temp TimeEnter Stop Time To 10 Seconds Enter Dryness LevelDRY Enter DRY Time 0 to 99 Minutes Enter Cycle AdjustmentDRY or Extra Extra DRY Controlled Cool Down Enter Cool Down Time 0 to 99 MinutesEnter Cool Down Temp 70 to 100 ºF Enter Cool DownSteam Injection Cycle Enter 1ST on Time 511 to From Previous Enter 2ND on Time Enter 3RD on Time Restoring Factory Default Settings Enter Password Confirm Defaults Defaults SET Default Settings YESCycle A-F Parameters Programs Preset by the Factory Cycle 0-40 Parameters Programs Preset by the FactoryPreprogrammed Cycles System Parameters Program Locations Fixed ParametersGas Diagnostic L.E.D. Display Fault Messages StandardsPage Page Page S.S. Diagnostic Conditions INPUT/OUTPUT I/O Board L.E.D. Indicators Brhl RED L.E.DKeyboard Touch PAD Layout Customer Custom Parameter Settings Auto Programmed Cycle Page ADC Part No 08/19/08
Top Page Image Contents