American Dryer Corp Phase 7.2.2 user manual Enter Dryness Level, Enter Stop Time To 10 Seconds

Page 64

Press the up arrow

key to increment

the temp, the down

arrow key to decrement the temp or enter the temp directly.

From

Previous

(A)

1

7

5

From

Previous

(B)

	2	Press the up arrow
	2	key to increment
		the time, the down
		arrow key to
	5	decrement the time
	5	or enter the time
		or enter the time
		directly.

25

175

Press ENTER to store

new changes

2: ENTER

DRYNESS LEVEL

Press ENTER to access

DRY

Next

Page (A)

Press ENTER to store

new changes

ENTER STOP TIME 5

TO 10 SECONDS

5

	Press the up
	arrow key to
7	increment the
	time, the down
	arrow key to
	decrement the
	time or enter
	the time
	directly.

7

Next

Page (B)

62

Image 64

Contents NON-COIN Retain This Manual In a Safe Place For Future Reference Table of Contents Section Phase 7 NON-COIN Auto Cycle Patent no ,827,627 Section Features Keyboard Touch Pad Symbols = STOP/CLEAR key Program Selections Preprogrammed CyclesPage Automatic Drying Cycle Patent no ,827,627 Operations Manually Loaded CyclesTimed Manual Drying Cycle Operation Temperature Conversion Status Cycle in Progress Temperature DisplayLight Emitting Diode L.E.D. DOT Matrix Display Audio Alert on Times 0 to Wrinkle Guard ProgramPreprogrammed Cycle Preview Reversing Option DiagnosticsProgram Locations Page Preprogrammed Locations for Custom Drying Operating Instructions Operating SequencePage Page MAN Operating Notes System Reset Fire Suppression System F.S.S. Theory of OperationFire Suppression System F.S.S. Valve Check Page D. Display Messages E.D. Display Operating StatusProgramming Instructions Introduction to ProgrammingPage Programming Flowcharts START/ENTER STOP/CLEARPhase Menu Programming Procedure Page Auto Reverse Mode On OFF Selecting Languages 0SELECT LanguageEnglish EspanolDryer Setup Selecting a Dryer ModelSelect System Parameters Select ModelGAS Reversing GAS REVERSING, Electric REVERSING, Steam REVERSING, GAS NONSteam NON-REVERSING Electric ReversingSelecting the System Temperature DEG F Enter Lint Cleaning Frequency 1 to 10 HoursDEG C Setting the Lint Cleaning Frequency Enter Audio Alert on Times 0 to Adjusting the Audio Alert On times System Temp Rotation Sensor Rotation Sensor Press Enter to jump directly to the location OFF Board Address 00 to ZZDryer Address To ZZ Auto Cycle Time OUT to 99 Minutes Auto Cycle Time Out System Temp Enter Lint Cleaning Frequency 1 to 10 Hours Enter Audio Alert on Times 0 to Rotation SensorAuto Cycle Time OUT To 99 Minutes Adjusting Reversing Spin Time and Stop Time Enter Spin Time 30 to 120 Seconds Reversing SetupEnter Stop Time 5 to 10 Seconds Press the up arrow key to increment Setup Wrinkle Guard Audio AlertWrinkle Guard Setup Wrinkle Guard Audio AlertSteam Injection Setup Wrinkle Guard Setup Steam Injection Setup Enter 1ST on Time Cycle511 to 000 First time adjustment is Minutes mm Enter 1ST OFF TimeEnter 2ND on Time Enter 3RD on Time Program 0-40 CyclesProgramming a F Cycles or 0 40 Cycles Program System Cycles ParametersReverse Mode Select a F KEYSelect Cycle Type AutoNot Available Enter DRY TempOFF Not Available TimeDRY Enter Dryness LevelEnter Stop Time To 10 Seconds DRY or Extra Extra DRY Enter Cycle AdjustmentEnter DRY Time 0 to 99 Minutes Controlled Cool Down Enter Cool Down Time 0 to 99 MinutesEnter Cool Down Temp 70 to 100 ºF Enter Cool DownSteam Injection Cycle Enter 1ST on Time 511 to From Previous Enter 2ND on Time Enter 3RD on Time Restoring Factory Default Settings Enter Password Confirm Defaults Defaults SET Default Settings YESCycle A-F Parameters Programs Preset by the Factory Cycle 0-40 Parameters Programs Preset by the FactoryPreprogrammed Cycles System Parameters Program Locations Fixed ParametersGas Diagnostic L.E.D. Display Fault Messages StandardsPage Page Page S.S. Diagnostic Conditions INPUT/OUTPUT I/O Board L.E.D. Indicators Brhl RED L.E.DKeyboard Touch PAD Layout Customer Custom Parameter Settings Auto Programmed Cycle Page ADC Part No 08/19/08