Hand Held Products manual Calibrating the Quick Check 600/800 Verifier, To turn off the unit

Page 18

3.c To clear (delete) the records stored in the memory, press ↓ and → to place the cursor on the asterisk next to the term Clear and then press SELECT. The stored results and the result from the last scan are deleted from the Quick Check 600/800 Verifier’s memory.

♦To turn off the unit:

1.Press and hold down POWER for about two seconds until the unit beeps once and clears the display.

OR

Let the unit turn itself off.

If the unit is connected to a charger, it turns off after ten

minutes of inactivity. If the unit is not connected to a charger, it turns off after one minute of inactivity.

Note: If the unit turned itself off and you want to review the results of the last scan, press POWER to turn on the unit and then press ←. The results from the last scan appear.

Calibrating the Quick Check 600/800 Verifier

Even though the verifier is calibrated at the factory, you should calibrate it before its first use to ensure its accuracy. For continued accuracy, periodically calibrate the unit during normal operation. You calibrate the unit using a reflectance page that is included in the pack of accessories. Each page has a serial number on it. For accurate calibration and data collection, you scan the reflectance page ten times and the Quick Check 600/800 Verifier performs a consistency test. If it passes, the unit is calibrated.

If, during the measurement of a symbol, a scan reflectance value of XX or — — appears on the display or on a printout, an out-of- range reading was recorded. Recalibrate the unit and then rescan the symbol.

The reflectance page is a precision standard made of photographic materials. If it becomes physically damaged or dirty, replace it to insure proper calibration. To order a new reflectance page, contact your sales representative.

♦To calibrate the Quick Check 600/800 Verifier:

1.Using the proper scan technique, scan the reflectance symbol from the accessory pack. You will hear a long beep followed by two short beeps after the first good scan, and the LCD displays REFLECTANCE CALIBRATION -9- More Scans!.

2.Continue to scan the reflectance page for a total of ten good scans. After each good scan, a single beep sounds and the display indicates how many good scans you need to obtain. After the tenth good scan, three beeps sound and the message Now Lift the Scanner Up off the Target appears. When you lift the scanner up, the opening display appears. To scan, set the wand scanner on a symbol’s quiet zone.

1 - 12

Quick Check® 600/800 Series User’s Guide

Page 17 Page 19
Image 18
Page 17 Page 19
Contents User’s Guide Disclaimer For European Community UsersWaste Electrical and Electronic Equipment Information Table of Contents Reviewing Scan Data Saving and Printing Chapter Customer Support Getting Started About This GuideSymbolDescription Power or Select or ↑, ↓, ←, → Unpacking the Quick Check 600/800 VerifierTerm in manual Term in software Noting the Verifier’s Features Quick Check 600/800 VerifierEAN/UPC LEDs Special FeaturesDisplay ButtonsPorts Specifications Installing the BatteriesSpecification To Install the Batteries Charging the BatteriesTo charge the batteries Turning the Unit On and Off To turn on the unitNo Printer Attached, then refer to .a Quick Check 600/800 Series User’s Guide Calibrating the Quick Check 600/800 Verifier To turn off the unitTo calibrate the Quick Check 600/800 Verifier To scan properly using a pen wand To scan properly using a mouse wandProperly Scanning With the Unit Cleaning the Wand Accessories and OptionsItem/DescriptionOrder code Documentation Quick Check 600/800 Series User’s Guide Quick Start Guide Review the option settings Print your scan resultsChanging the Settings Changing the SpecificationsSymbologies Symbologies Symbology Specifications Symbology Parameters defaults are in boldCheck Options Magnification FactorExpand U.P.C./EO Modes ShownCharacter Font & Tolerances Character Translation Table Code 128, Code 16K, and CodeFixed Message Length To modify the symbology optionsWide-to-Narrow Ratio → or SelectIndustry Applications Changing the Test Criteria Scan GradeTo select an application Decodability ISO/IEC gradesNumber of Scans To return to the previous menu, press Power Changing the Scanning OptionsTo change the test criteria Decode Direction Beeper PitchExtended Accuracy To change the scanning optionsChanging the Output Options Display OptionsParameter Result Lines Print Options AutoPrint/StoreScan Profile To change the output optionsTo change the display options To reset a unit Resetting the Default SettingsLocking the Settings To change the printout optionsUsing a Command Code About Command CodesC./EAN/JAN Enable On or Off Generic Code SelectionsChoosing a Command Code Customized Command CodesTo use a customized Command Code To create a customized Command CodeTo request a Command Code from Hand Held Products Quick Check 600/800 Series User’s Guide Reviewing Scan Data Reviewing Scan ResultsScan Grades ISO/IEC Symbol Grade Determining the ISO/IEC Symbol Grade Quick Check 600/800 Series User’s Guide To obtain the scan grade and ISO/IEC Symbol grade Reviewing a Scan ExampleQuick Check 600/800 Series User’s Guide LED Display To review data from the last scanAudio Sounds Bar growth LCD bar growth LED lit Tolerance used IndicationParameter Trad’l Reviewing the Dimensional ParametersErrors in Dimensional Parameters Parameter ResultTo review the dimensional parameters CalculatingReviewing the Reflectance Parameters Errors in Reflectance Parameters PCSSymbol Contrast, Minimum and Maximum Reflectance To review the reflectance parametersErrors in Format Parameters Reviewing the Format ParametersTo review the format procedures Reviewing MessagesUsing Sstr Codes to Review Data Sstr CodesSstr Code Type Test Criteria Name To return the customized display to the default display Using the Quick Check Verifier as a ReflectometerTo quickly review data using Sstr Codes To customize the result displayTo use the Quick Check Verifier as a static reflectometer Checking the Print Buffer During Operation Saving and PrintingSaving Data To save scan dataTo clear delete the records stored in the memory, press → Printing DataTo check the print buffer during operation To print current dataDeleting Stored Data To print stored dataTo stop printing Interfacing With a Computer Reviewing the PrintoutsTo delete stored data QCP and Qchsp Printouts Using the QCP or Qchsp Printing GuidelinesSwitch Position Function To set up the QCP or Qchsp To install or replace the QCP or Qchsp paper rollTo turn on and off the QCP or Qchsp To remove the ribbon from the QCP or Qchsp To perform a QCP or Qchsp self-test Troubleshooting the QCP or Qchsp Quick Check 600/800 Series User’s Guide Background Information General Bar Code InformationSymbology Specifications Symbology Industries OrganizationGS1 formerly UCC and EAN Symbology Characteristics Quick Check 600/800 Series User’s Guide Symbology Character Set Widths How a Bar Code Verifier WorksElement Additional Information Quick Check 600/800 Series User’s Guide Downloading DataMatch Structuring and Loading the Database Using DataMatchUnderstanding the DataMatch Feature SYM Identifier CodeDecode To load the database into the verifierQuick Check 600/800 Series User’s Guide Selecting the DataMatch Feature To select DataMatchReviewing DataMatch Results Quick Check 600/800 Series User’s Guide Using a Quick Check 800 Verifier General OperationPercent Decoded/Scanned Mode Reflectance-Based InformationScanProfile Output Print Results Calculate Decoded/Scanned Change Settings Change Settings Test Criteria #Scans/Symbol nnn Error, Application, and Type Messages Type Display Message Printout MessageDatabase ECV /VCVS Bookland Quick Check 600/800 Series User’s Guide Ccbba Hibcc EAN ITF SCS /ITF EAN SCS Quick Check 600/800 Series User’s Guide Flow Charts Quick Check 600/800 Series User’s Guide Quick Check 600/800 Series User’s Guide Quick Check 600/800 Series User’s Guide Quick Check 600/800 Series User’s Guide Quick Check 600/800 Series User’s Guide Sstr Codes Quick Check 600/800 Series User’s Guide Special Codes Quick Check 600/800 Series User’s Guide Unrecognized Symbols Unrecognized SymbolsQuick Check 600/800 Series User’s Guide Customer Support TroubleshootingTo restore the display To check the software versionLatin America Limited Warranty Quick Check 600/800 Series User’s Guide Page Hand Held Products, Inc
Top Page Image Contents