Hand Held Products 800, 600 manual Print Options, AutoPrint/Store

Page 37

Additional results you can display and the criteria used include:

•Symbol type

•Wide-to-narrow ratio (traditional)

•Light reflectance (traditional and ISO/IEC)

•Dark reflectance (traditional and ISO/IEC)

•Symbol contrast (ISO/IEC)

•Reflectance minimum/maximum (ISO/IEC)

•Edge contrast minimum (ISO/IEC)

•Defects (ISO/IEC)

•Message length

•Bar growth (traditional)

Error override allows you to set the verifier to replace the default or user-selected Upper and Lower Parameter Result lines with any error information or messages that might result from the bar code scan analysis. If more than two errors result from a scan, the first two appear on the display and you can scroll the display to view the other errors. The default for Error Override is NO.

When you select ISO/IEC criteria, you can use the LED’s display feature to set the LEDs to indicate bar growth/loss or pass/fail grade and result grade. In addition, when you select ISO/IEC criteria, the five multi-colored LEDs normally indicate symbol pass or fail based on the ISO/IEC criteria. With the LED feature set to Bar Growth, the LEDs provide information on bar growth or loss, just as they would if you selected traditional pass/fail test criteria.

Print Options

The print options allow you to select:

•Printer type (QCP or QCHSP)

•Printout form (long or short)

•Automatic options — automatically print data when the unit is connected to a printer and turned on, automatically store data when the unit is not connected to a printer

•Auto Print/Store with or without Profile

You can use any one of the three optional accessory hardcopy printers, but you need to select the printer before you try to print. Supported printers include:

•QCP (standard printer)

•QCHSP (High-Speed Printer)

Refer to Chapter 5, Saving and Printing for more information about these printers.

AutoPrint/Store

The AutoPrint/Store option automatically prints or stores your data:

•When you have the AutoPrint/Store feature turned on and a printer connected to your verifier and turned on, your scan results print automatically. You cannot store results when a printer is connected and turned on.

Quick Check® 600/800 Series User’s Guide

3 - 13

Image 37

Contents User’s Guide For European Community Users DisclaimerWaste Electrical and Electronic Equipment Information Table of Contents Reviewing Scan Data Saving and Printing Chapter Customer Support About This Guide Getting StartedUnpacking the Quick Check 600/800 Verifier SymbolDescription Power or Select or ↑, ↓, ←, →Term in manual Term in software Quick Check 600/800 Verifier Noting the Verifier’s FeaturesEAN/UPC Display Special FeaturesLEDs ButtonsPorts Installing the Batteries SpecificationsSpecification Charging the Batteries To Install the BatteriesTo charge the batteries To turn on the unit Turning the Unit On and OffNo Printer Attached, then refer to .a Quick Check 600/800 Series User’s Guide To turn off the unit Calibrating the Quick Check 600/800 VerifierTo calibrate the Quick Check 600/800 Verifier To scan properly using a mouse wand To scan properly using a pen wandProperly Scanning With the Unit Accessories and Options Cleaning the WandItem/DescriptionOrder code Documentation Quick Check 600/800 Series User’s Guide Quick Start Guide Print your scan results Review the option settingsChanging the Specifications Changing the SettingsSymbologies Symbologies Symbology Parameters defaults are in bold Symbology SpecificationsExpand U.P.C./EO Magnification FactorCheck Options Modes ShownCharacter Translation Table Code 128, Code 16K, and Code Character Font & TolerancesWide-to-Narrow Ratio To modify the symbology optionsFixed Message Length → or SelectIndustry Applications Scan Grade Changing the Test CriteriaTo select an application ISO/IEC grades DecodabilityNumber of Scans Changing the Scanning Options To return to the previous menu, press PowerTo change the test criteria Extended Accuracy Beeper PitchDecode Direction To change the scanning optionsDisplay Options Changing the Output OptionsParameter Result Lines AutoPrint/Store Print OptionsTo change the output options Scan ProfileTo change the display options Locking the Settings Resetting the Default SettingsTo reset a unit To change the printout optionsAbout Command Codes Using a Command CodeGeneric Code Selections C./EAN/JAN Enable On or OffCustomized Command Codes Choosing a Command CodeTo create a customized Command Code To use a customized Command CodeTo request a Command Code from Hand Held Products Quick Check 600/800 Series User’s Guide Reviewing Scan Results Reviewing Scan DataScan Grades ISO/IEC Symbol Grade Determining the ISO/IEC Symbol Grade Quick Check 600/800 Series User’s Guide Reviewing a Scan Example To obtain the scan grade and ISO/IEC Symbol gradeQuick Check 600/800 Series User’s Guide To review data from the last scan LED DisplayBar growth LCD bar growth LED lit Tolerance used Indication Audio SoundsErrors in Dimensional Parameters Reviewing the Dimensional ParametersParameter Trad’l Parameter ResultCalculating To review the dimensional parametersReviewing the Reflectance Parameters PCS Errors in Reflectance ParametersTo review the reflectance parameters Symbol Contrast, Minimum and Maximum ReflectanceReviewing the Format Parameters Errors in Format ParametersReviewing Messages To review the format proceduresSstr Codes Using Sstr Codes to Review DataSstr Code Type Test Criteria Name To quickly review data using Sstr Codes Using the Quick Check Verifier as a ReflectometerTo return the customized display to the default display To customize the result displayTo use the Quick Check Verifier as a static reflectometer Saving Data Saving and PrintingChecking the Print Buffer During Operation To save scan dataTo check the print buffer during operation Printing DataTo clear delete the records stored in the memory, press → To print current dataTo print stored data Deleting Stored DataTo stop printing Reviewing the Printouts Interfacing With a ComputerTo delete stored data QCP and Qchsp Printouts Printing Guidelines Using the QCP or QchspSwitch Position Function To install or replace the QCP or Qchsp paper roll To set up the QCP or QchspTo turn on and off the QCP or Qchsp To remove the ribbon from the QCP or Qchsp To perform a QCP or Qchsp self-test Troubleshooting the QCP or Qchsp Quick Check 600/800 Series User’s Guide General Bar Code Information Background InformationSymbology Industries Organization Symbology SpecificationsGS1 formerly UCC and EAN Symbology Characteristics Quick Check 600/800 Series User’s Guide How a Bar Code Verifier Works Symbology Character Set WidthsElement Additional Information Quick Check 600/800 Series User’s Guide Understanding the DataMatch Feature Using DataMatchDownloading DataMatch Structuring and Loading the Database SYM Identifier CodeTo load the database into the verifier DecodeQuick Check 600/800 Series User’s Guide To select DataMatch Selecting the DataMatch FeatureReviewing DataMatch Results Quick Check 600/800 Series User’s Guide General Operation Using a Quick Check 800 VerifierReflectance-Based Information Percent Decoded/Scanned ModeScanProfile Output Print Results Calculate Decoded/Scanned Change Settings Change Settings Test Criteria #Scans/Symbol nnn Type Display Message Printout Message Error, Application, and Type MessagesDatabase ECV /VCVS Bookland Quick Check 600/800 Series User’s Guide Ccbba Hibcc EAN ITF SCS /ITF EAN SCS Quick Check 600/800 Series User’s Guide Flow Charts Quick Check 600/800 Series User’s Guide Quick Check 600/800 Series User’s Guide Quick Check 600/800 Series User’s Guide Quick Check 600/800 Series User’s Guide Quick Check 600/800 Series User’s Guide Sstr Codes Quick Check 600/800 Series User’s Guide Special Codes Quick Check 600/800 Series User’s Guide Unrecognized Symbols Unrecognized SymbolsQuick Check 600/800 Series User’s Guide To restore the display TroubleshootingCustomer Support To check the software versionLatin America Limited Warranty Quick Check 600/800 Series User’s Guide Page Hand Held Products, Inc