Hand Held Products 600, 800 manual To turn on and off the QCP or Qchsp, To set up the QCP or Qchsp

Page 70

The printer has a replaceable cartridge ribbon. Replace the paper roll when it is empty.

♦To turn on and off the QCP or QCHSP:

1.To turn on the printer, press the power switch into the On (center) position.

2.To turn off the printer, press the power switch into the Off (down left) position. After you turn off the printer, wait at least three seconds to turn on the power for the proper initialization procedure.

♦To set up the QCP or QCHSP:

1.Place the printer on a hard, flat surface such as a table or desk top.

2.Press the power switch into the Off (down left) position.

3.Plug the power connector from the transformer into the printer.

4.Plug the transformer into a VAC wall outlet.

♦To install or replace the QCP or QCHSP paper roll:

1.Press the printer power switch to the Off (down left) position.

2.Remove the printer cover by locating the four small grooves embossed on each side of the printer cover and tilting the cover open by pushing down gently on both sets of these grooves.

3.If necessary, remove the empty roll. Press and hold the power switch in the Paper Feed (down right) position to advance the paper about one inch beyond the paper cutter.

Lift the empty roll from the printer housing.

Do not pull paper out of the back of the printer as this will damage the mechanism.

WARNING

4.Unroll several inches of paper from a new roll and cut a straight edge on the paper if it is jagged or wrinkled. (A straight edge helps guide the paper into the printer.)

5 - 8

Quick Check® 600/800 Series User’s Guide

Image 70

Contents User’s Guide For European Community Users DisclaimerWaste Electrical and Electronic Equipment Information Table of Contents Reviewing Scan Data Saving and Printing Chapter Customer Support Getting Started About This GuideUnpacking the Quick Check 600/800 Verifier SymbolDescription Power or Select or ↑, ↓, ←, →Term in manual Term in software Noting the Verifier’s Features Quick Check 600/800 VerifierEAN/UPC LEDs Special FeaturesDisplay ButtonsPorts Installing the Batteries SpecificationsSpecification Charging the Batteries To Install the BatteriesTo charge the batteries Turning the Unit On and Off To turn on the unitNo Printer Attached, then refer to .a Quick Check 600/800 Series User’s Guide To turn off the unit Calibrating the Quick Check 600/800 VerifierTo calibrate the Quick Check 600/800 Verifier To scan properly using a mouse wand To scan properly using a pen wandProperly Scanning With the Unit Accessories and Options Cleaning the WandItem/DescriptionOrder code Documentation Quick Check 600/800 Series User’s Guide Quick Start Guide Review the option settings Print your scan resultsChanging the Specifications Changing the SettingsSymbologies Symbologies Symbology Specifications Symbology Parameters defaults are in boldCheck Options Magnification FactorExpand U.P.C./EO Modes ShownCharacter Font & Tolerances Character Translation Table Code 128, Code 16K, and CodeFixed Message Length To modify the symbology optionsWide-to-Narrow Ratio → or SelectIndustry Applications Scan Grade Changing the Test CriteriaTo select an application ISO/IEC grades DecodabilityNumber of Scans Changing the Scanning Options To return to the previous menu, press PowerTo change the test criteria Decode Direction Beeper PitchExtended Accuracy To change the scanning optionsDisplay Options Changing the Output OptionsParameter Result Lines Print Options AutoPrint/StoreTo change the output options Scan ProfileTo change the display options To reset a unit Resetting the Default SettingsLocking the Settings To change the printout optionsUsing a Command Code About Command CodesC./EAN/JAN Enable On or Off Generic Code SelectionsChoosing a Command Code Customized Command CodesTo create a customized Command Code To use a customized Command CodeTo request a Command Code from Hand Held Products Quick Check 600/800 Series User’s Guide Reviewing Scan Results Reviewing Scan DataScan Grades ISO/IEC Symbol Grade Determining the ISO/IEC Symbol Grade Quick Check 600/800 Series User’s Guide To obtain the scan grade and ISO/IEC Symbol grade Reviewing a Scan ExampleQuick Check 600/800 Series User’s Guide LED Display To review data from the last scanAudio Sounds Bar growth LCD bar growth LED lit Tolerance used IndicationParameter Trad’l Reviewing the Dimensional ParametersErrors in Dimensional Parameters Parameter ResultTo review the dimensional parameters CalculatingReviewing the Reflectance Parameters Errors in Reflectance Parameters PCSSymbol Contrast, Minimum and Maximum Reflectance To review the reflectance parametersErrors in Format Parameters Reviewing the Format ParametersTo review the format procedures Reviewing MessagesSstr Codes Using Sstr Codes to Review DataSstr Code Type Test Criteria Name To return the customized display to the default display Using the Quick Check Verifier as a ReflectometerTo quickly review data using Sstr Codes To customize the result displayTo use the Quick Check Verifier as a static reflectometer Checking the Print Buffer During Operation Saving and PrintingSaving Data To save scan dataTo clear delete the records stored in the memory, press → Printing DataTo check the print buffer during operation To print current dataTo print stored data Deleting Stored DataTo stop printing Reviewing the Printouts Interfacing With a ComputerTo delete stored data QCP and Qchsp Printouts Using the QCP or Qchsp Printing GuidelinesSwitch Position Function To install or replace the QCP or Qchsp paper roll To set up the QCP or QchspTo turn on and off the QCP or Qchsp To remove the ribbon from the QCP or Qchsp To perform a QCP or Qchsp self-test Troubleshooting the QCP or Qchsp Quick Check 600/800 Series User’s Guide Background Information General Bar Code InformationSymbology Specifications Symbology Industries OrganizationGS1 formerly UCC and EAN Symbology Characteristics Quick Check 600/800 Series User’s Guide How a Bar Code Verifier Works Symbology Character Set WidthsElement Additional Information Quick Check 600/800 Series User’s Guide Downloading DataMatch Structuring and Loading the Database Using DataMatchUnderstanding the DataMatch Feature SYM Identifier CodeDecode To load the database into the verifierQuick Check 600/800 Series User’s Guide Selecting the DataMatch Feature To select DataMatchReviewing DataMatch Results Quick Check 600/800 Series User’s Guide Using a Quick Check 800 Verifier General OperationReflectance-Based Information Percent Decoded/Scanned ModeScanProfile Output Print Results Calculate Decoded/Scanned Change Settings Change Settings Test Criteria #Scans/Symbol nnn Error, Application, and Type Messages Type Display Message Printout MessageDatabase ECV /VCVS Bookland Quick Check 600/800 Series User’s Guide Ccbba Hibcc EAN ITF SCS /ITF EAN SCS Quick Check 600/800 Series User’s Guide Flow Charts Quick Check 600/800 Series User’s Guide Quick Check 600/800 Series User’s Guide Quick Check 600/800 Series User’s Guide Quick Check 600/800 Series User’s Guide Quick Check 600/800 Series User’s Guide Sstr Codes Quick Check 600/800 Series User’s Guide Special Codes Quick Check 600/800 Series User’s Guide Unrecognized Symbols Unrecognized SymbolsQuick Check 600/800 Series User’s Guide Customer Support TroubleshootingTo restore the display To check the software versionLatin America Limited Warranty Quick Check 600/800 Series User’s Guide Page Hand Held Products, Inc