Hand Held Products 800, 600 manual Beeper Pitch, Extended Accuracy, Decode Direction

Page 35

•Beeper Pitch (raise or lower)

•Extended Accuracy

•Decoding direction (both ways or forward only)

Beeper Pitch

You can change the pitch of the verifier’s beeper. Higher pitches seem to sound louder. You can also turn off the tone. The default is 16. The range includes Off and 1 through 31.

Extended Accuracy

The Extended Accuracy setting is the number of scans of the same symbol, taken at the same path in the symbol, that yields the scan grade.

•With Extended Accuracy on, individual parameter measurements and results are averaged over successive scans of the symbol. Using the extended accuracy mode greatly reduces reading variability due to variations in scanning motion and minor scan path variations. When Extended Accuracy is on, you select the number of scans for the averaged result from 2 through 10, 12, 15, 20, 30, 50 and 100.

•When Extended Accuracy is off (set to one), each scan of the symbol gives the measured results. The default is Extended Accuracy turned off.

When you scan a symbol with Extended Accuracy on, a numeric counter appears on the display telling you how many additional scans of the same path you must obtain. After you satisfy the setting, the scan grade appears. If you do not scan the same symbol within five seconds, the unit assumes you do not want to satisfy the Extended Accuracy setting you chose and displays the scan results from that individual scan. If you scan a different symbol after your first scan, the Extended Accuracy counter resets.

For further discussion and comparison of scan grade to symbol grade, refer to Chapter 4, Reviewing Scan Data.

Decode Direction

You can set the Quick Check 600/800 Verifier to read bar code symbols from left- to-right, called “forward only,” or from either direction, called “Both Ways.” The BothWays setting (default) makes scanning easier and more flexible than forward-only scanning.

♦To change the scanning options:

1.Display the menu that begins with Print Results (press POWER and SELECT).

2.Set the cursor on the asterisk next to Change Settings and then press

SELECT.

A menu that begins with Specifications appears.

Quick Check® 600/800 Series User’s Guide

3 - 11

Image 35

Contents User’s Guide Waste Electrical and Electronic Equipment Information DisclaimerFor European Community Users Table of Contents Reviewing Scan Data Saving and Printing Chapter Customer Support About This Guide Getting StartedTerm in manual Term in software SymbolDescription Power or Select or ↑, ↓, ←, →Unpacking the Quick Check 600/800 Verifier Quick Check 600/800 Verifier Noting the Verifier’s FeaturesEAN/UPC Buttons Special FeaturesDisplay LEDsPorts Specification SpecificationsInstalling the Batteries To charge the batteries To Install the BatteriesCharging the Batteries To turn on the unit Turning the Unit On and OffNo Printer Attached, then refer to .a Quick Check 600/800 Series User’s Guide To calibrate the Quick Check 600/800 Verifier Calibrating the Quick Check 600/800 VerifierTo turn off the unit Properly Scanning With the Unit To scan properly using a pen wandTo scan properly using a mouse wand Item/DescriptionOrder code Cleaning the WandAccessories and Options Documentation Quick Check 600/800 Series User’s Guide Quick Start Guide Print your scan results Review the option settingsSymbologies Changing the SettingsChanging the Specifications Symbologies Symbology Parameters defaults are in bold Symbology SpecificationsModes Shown Magnification FactorExpand U.P.C./EO Check OptionsCharacter Translation Table Code 128, Code 16K, and Code Character Font & Tolerances→ or Select To modify the symbology optionsWide-to-Narrow Ratio Fixed Message LengthIndustry Applications To select an application Changing the Test CriteriaScan Grade Number of Scans DecodabilityISO/IEC grades To change the test criteria To return to the previous menu, press PowerChanging the Scanning Options To change the scanning options Beeper PitchExtended Accuracy Decode DirectionParameter Result Lines Changing the Output OptionsDisplay Options AutoPrint/Store Print OptionsTo change the display options Scan ProfileTo change the output options To change the printout options Resetting the Default SettingsLocking the Settings To reset a unitAbout Command Codes Using a Command CodeGeneric Code Selections C./EAN/JAN Enable On or OffCustomized Command Codes Choosing a Command CodeTo request a Command Code from Hand Held Products To use a customized Command CodeTo create a customized Command Code Quick Check 600/800 Series User’s Guide Scan Grades Reviewing Scan DataReviewing Scan Results ISO/IEC Symbol Grade Determining the ISO/IEC Symbol Grade Quick Check 600/800 Series User’s Guide Reviewing a Scan Example To obtain the scan grade and ISO/IEC Symbol gradeQuick Check 600/800 Series User’s Guide To review data from the last scan LED DisplayBar growth LCD bar growth LED lit Tolerance used Indication Audio SoundsParameter Result Reviewing the Dimensional ParametersErrors in Dimensional Parameters Parameter Trad’lCalculating To review the dimensional parametersReviewing the Reflectance Parameters PCS Errors in Reflectance ParametersTo review the reflectance parameters Symbol Contrast, Minimum and Maximum ReflectanceReviewing the Format Parameters Errors in Format ParametersReviewing Messages To review the format proceduresSstr Code Type Test Criteria Name Using Sstr Codes to Review DataSstr Codes To customize the result display Using the Quick Check Verifier as a ReflectometerTo quickly review data using Sstr Codes To return the customized display to the default displayTo use the Quick Check Verifier as a static reflectometer To save scan data Saving and PrintingSaving Data Checking the Print Buffer During OperationTo print current data Printing DataTo check the print buffer during operation To clear delete the records stored in the memory, press →To stop printing Deleting Stored DataTo print stored data To delete stored data Interfacing With a ComputerReviewing the Printouts QCP and Qchsp Printouts Printing Guidelines Using the QCP or QchspSwitch Position Function To turn on and off the QCP or Qchsp To set up the QCP or QchspTo install or replace the QCP or Qchsp paper roll To remove the ribbon from the QCP or Qchsp To perform a QCP or Qchsp self-test Troubleshooting the QCP or Qchsp Quick Check 600/800 Series User’s Guide General Bar Code Information Background InformationSymbology Industries Organization Symbology SpecificationsGS1 formerly UCC and EAN Symbology Characteristics Quick Check 600/800 Series User’s Guide Element Symbology Character Set WidthsHow a Bar Code Verifier Works Additional Information Quick Check 600/800 Series User’s Guide SYM Identifier Code Using DataMatchUnderstanding the DataMatch Feature Downloading DataMatch Structuring and Loading the DatabaseTo load the database into the verifier DecodeQuick Check 600/800 Series User’s Guide To select DataMatch Selecting the DataMatch FeatureReviewing DataMatch Results Quick Check 600/800 Series User’s Guide General Operation Using a Quick Check 800 VerifierScanProfile Output Percent Decoded/Scanned ModeReflectance-Based Information Print Results Calculate Decoded/Scanned Change Settings Change Settings Test Criteria #Scans/Symbol nnn Type Display Message Printout Message Error, Application, and Type MessagesDatabase ECV /VCVS Bookland Quick Check 600/800 Series User’s Guide Ccbba Hibcc EAN ITF SCS /ITF EAN SCS Quick Check 600/800 Series User’s Guide Flow Charts Quick Check 600/800 Series User’s Guide Quick Check 600/800 Series User’s Guide Quick Check 600/800 Series User’s Guide Quick Check 600/800 Series User’s Guide Quick Check 600/800 Series User’s Guide Sstr Codes Quick Check 600/800 Series User’s Guide Special Codes Quick Check 600/800 Series User’s Guide Unrecognized Symbols Unrecognized SymbolsQuick Check 600/800 Series User’s Guide To check the software version TroubleshootingTo restore the display Customer SupportLatin America Limited Warranty Quick Check 600/800 Series User’s Guide Page Hand Held Products, Inc